This paper presents the modelling and simulation of a low-power Brushless DC machine in a Rotor Flux Oriented mode in MATLAB/Simulink. The modelling of the machine is presented in the synchronous dq frame. Using this model suitable Proportional Integral controllers have been designed for the Rotor Flux Oriented speed and current loops. Sensorless simulation estimates obtained from a back-emf observer for both electrical angle and rotor speed are presented. The dynamic response of the model is also shown in sensorless closed-loop whereby the estimates obtained are used for control purposes. The error in the estimated position and speed during closed-loop are kept below 1.9 % and 0.1 % respectively such that the speed controlled system is stable throughout a wide range of speeds.
Electromyography (EMG) signals are commonly used by researchers to study kinesiology, which can then be used to control prosthetic arms, hands and limbs [1]. Additionally, EMG signals are used in the field of Bio Robotics for gesture control applications. The aim of this work is to implement a set of affordable active electrodes for the classification of finger movement via time-domain analysis. The electromyography signals are received through the Ag-AgCI electrodes, which are conductive materials used for gathering and transferring the muscle activation potential. The proposed paper focuses on presenting a new low-cost based system for the classification of human finger movement using auto-gain adjustment active electrodes. Different people will have different EMG amplitudes; therefore, it is difficult to determine the gain required prior performing further signal processing. In this work the implementation of an auto-adjustable gain amplifier was used. This circuit monitors the maximum EMG signal amplitude and adjusts the gain stage accordingly, without any user interaction. This ensures that the gain is always automatically adjusted to get the most effective performance from the data acquisition or analogue to digital converter (ADC) module since the signal will be neither too low in amplitude to cause inefficient use of the ADC resolution, not too high to cause saturation of the signal. Additionally, the instrumentation amplifier is directly interfaced near the Ag-AgCI electrodes. Through extensive experiments, our sEMG sensor outperforms a widely used commercially available product and when tested under ten different persons our low cost EMG data acquisition system achieves reproducible and repeatable results for the detection and classification of finger movements.
Modern power electronic circuits typically require an on-board microcontroller to carry out necessary sensor measurements and controlled semiconductor switching. Hence, in the prototyping stage it is convenient to have a microcontroller development board designed for noise immunity and best electromagnetic compatibility possible. Typical development boards provided by manufacturers are not designed to such a specification due to cost considerations. This paper presents the design of an improved development board for the STM32F4 microcontroller for better performance in switching power converter circuits.
Estimating the behaviour of buckling clamped–clamped beams entails solving nonlinear partial differential equations (PDEs). Several techniques are found in the literature that deal with such PDEs; techniques that also take into account initial curvatures and/or imperfections. However, when the system configuration is different from that of one single beam it becomes more involved. In this Letter, a buckling energy harvester is presented. Owing to the nature of its design, a nonlinear differential equation (not a PDE) capable of capturing all the salient characteristics of its behaviour could be developed. The effectiveness of the model is validated using finite element analysis. The energy harvester is designed using the SINTEF piezoVolume process and operated in the d31 mode. With electrical damping only, the device, designed for validation purposes, achieved a power density of 0.13 mW cm −3 at 3.5 g ms −2 at 560 Hz and produced d31 open‐circuit voltages of 0.6 V.
In this paper two MEMS structures that are intended to demodulate a BPSK low data rate signal are compared. They are designed in conformity with the MetalMUMPs process. Target applications for such devices would be low-rate, wireless personal area networks (LR-WPANs) such as those described in the IEEE 802.15.4 standard onto which the ZigBee standard is built. The presented MEMS structures mix the Radio Frequency (RF) and Local Oscillator (LO) signals electrostatically and also filter this mixed signal prior to electrostatic sensing. These MEMS structures can also be used as the building blocks to demodulate higher order PSK schemes. The first structures' mode of vibration is torsional in nature and the use of torsional vibrations for BPSK demodulation is innovative. The first structure has an undamped resonant frequency of 2 MHz. The second structure is an extension of the first and is also supported on tethers exhibiting torsional vibrations. This structure resonates at 680 kHz.
The results presented show that a simple microstructure involving a plate supported by two tethers can exhibit varied dynamics due to its nonlinearities. The plate vibrates such that the tethers experience a torsional twisting and it is designed within the constraints imposed by the MetalMUMPs process. Each region of operation has different applications and one can traverse through these regions by adjusting the sensing and actuation voltages. As one would expect, the nonlinearities dominate at higher voltages, with the first signs of chaotic trajectories appearing at 75 V. Parameters of the nonlinear model are first determined from finite‐element analysis responses, and results from subsequent numerical simulations for each region are presented.