Peng Zhao

Prof. Peng Zhao


Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 March 2022 in Materials
Verified
Journal Article
Open access
PDF file
PZPeng Zhao
Peng Zhao
Rongxun PiaoRongxun Piao
Rongxun Piao
ZZZongshu Zou
Zongshu Zou
Understanding the essence of the flow oscillations within a submerged-entry nozzle (SEN) is essential to control flow patterns in the continuous casting mold and consequently increase the superficial quality of steel products. A numerical study of the mesoscopic fluid-particle flow in a bifurcated pool-type SEN under steady operating conditions is conducted using the lattice Boltzmann method (LBM) coupled with the large eddy simulation (LES) model. The accuracy of the model has been verified by comparing vortex structures and simulated velocities with published experimental values. The LBM modeling is also verified by comparing the “stair-step” jet patterns observed in the experiment. The geometrical parameters and operational conditions of physical experiments are reproduced in the simulations. By comparing the time-averaged velocities of Reynolds-averaged Navier–Stokes equations (RANS) with LBM models, transient mesoscopic fluid-particles and related vortex structures can be better reproduced within the SEN. The visualization of internal flow within the SEN is illustrated through the mass-less Discrete Phase Model (DPM) model. The trajectories show that the LBM–LES–DPM coupled model is good at predicting the transient vortical flow within the SEN. A large vortex is found inside the exit port and continuously changes in shape and size therein. The monitoring points and lines within the SEN are selected to illustrate the velocity variations and effective viscosity, which can reflect the oscillating characteristics even under stable operating conditions without changes at the exit from the SEN. Furthermore, the formation, development, diffusion, and dissipation of the vortex structures from the exit port of the SEN are also investigated using the Q criteria. The comparison of the power spectrum with high-frequency components along the exit port indicates that the flow oscillations must originate from within the SEN and are intensified in the exit port. The mesoscopic LBM model can replicate the fluid-particle flow and vortex structure transmission as well as their turbulence effects inside the SEN in detail.

28 March 2022 in Metals
Verified
Journal Article
Open access
PDF file
PZPeng Zhao
Peng Zhao
Rongxun PiaoRongxun Piao
Rongxun Piao
Transient phenomena and vortex structures throughout the mold are simulated using a lattice Boltzmann method (LBM) coupled with large eddy simulation (LES) using a free surface model under steady operating conditions. The accuracy of the LBM-LES model has been verified by comparing the simulated velocities with published experimental values. The current work focuses on the evolution of the vortex structure in internal flow inside the submerged entry nozzle (SEN) jet flow and the turbulent flow near the wall of the mold. The results show various types of vortex structures with different directions are presented during the jet impingement, including the “ring, rib, and horseshoe”-like shaped vortices in the simulation, resulting in complex turbulent flow near the wall of the mold. Vortices structures are then identified and compared by different vorticial criteria, including vortex methods (ω), Q method, λ2 method (Lambda-2), Δ method (Delta), and Ω method (Omega). The formation, development, and dissipation of the vortex structures and their effects on turbulence are investigated. The results indicate that the turbulent flow (viscosity) can reflect changes in asymmetric vortices structures and flow patterns (via crossflow), which can reflect the periodical flow in the mold. Flow oscillation frequencies are mainly concentrated in the range of 0.3 Hz in this simulation. The oscillations are not a simple combination of frequency modes of crossflow in the mold. These new studies can elucidate the mechanism of vortex structure distributions in representative flow regions of the continuous casting mold.

27 August 2022 in Materials
Verified
Journal Article
Open access
PDF file
Rongxun PiaoRongxun Piao
Rongxun Piao
WZWenjin Zhu
Wenjin Zhu
LMLan Ma
Lan Ma
PZPeng Zhao
Peng Zhao
BHBiao Hu
Biao Hu
TiH2-basd powder metallurgy (PM) is one of the effective ways to prepared high temperature titanium alloy. To study the thermomechanical behavior of near-α titanium alloy and proper design of hot forming, isothermal compression test of TiH2-based PM near-α type Ti-5.05Al-3.69Zr-1.96Sn-0.32Mo-0.29Si (Ti-1100) alloy was performed at temperatures of 1123–1323 K, strain rates of 0.01-1 s−1, and maximum deformation degree of 60%. The hot deformation characteristics of alloy were analyzed by strain hardening exponent (n), strain rate sensitivity (m), and processing map, along with microstructure observation. The flow stress revealed that the difference in softening/hardening behavior at temperature of 1273–1323 K and the strain rate of 1 s−1 compared to the lower deformation temperature and strain rate. The strain hardening exponents at temperatures of 1123 K are all negative under all strain rates, and the most severe flow softening with minimum value of n was observed at 1123 K and 1 s−1. The strain rate sensitives showed that the peak region with m value greater than 0.5 generally appeared in the high temperature range of 1273–1323 K, while strain rate sensitivity at low temperature behaved differently with strain rates. The processing map developed for strain of 0.6 exhibited high power dissipation efficiency at high temperatures of 1273–1323 K and a low strain rate of 0.01 s−1, due to microstructure evolution of β phase. The decrease of strain rate at 1323 K resulted in the formation of globularization of α lamellae. The instability domain of flow behavior was identified in the temperature range of 1123–1173 K and at the strain rate higher than 0.01 s−1 reflecting the localized plastic flow and adiabatic shear banding, and inhomogenous microstructure. The variation of power dissipation energy (η) slope with strain demonstrated that the power dissipation mechanism during hot deformation has been changed from temperature-dependent to microstructure-dependent with the increase of temperature for the alloy deformed at 0.1 s−1. Eventually, the optimum processing range to deform the material is at 1273–1323 K and a strain rate range of 0.01–0.165 s−1 (lnε˙ = −4.6–−1.8).