Xianjie Hao

Xianjie Hao


Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 May 2020 in Construction and Building Materials
Verified
Journal Article
Closed access
XHXianjie Hao
Xianjie Hao
SWShaohua Wang
Shaohua Wang
QXQuansheng Xu
Quansheng Xu
DYDequan Yang
Dequan Yang
QZQian Zhang
Qian Zhang
YWYingnan Wei
Yingnan Wei

15 August 2022 in Tunnelling and Underground Space Technology
Verified
Journal Article
Closed access
XHXianjie Hao
Xianjie Hao
LYLiang Yuan
Liang Yuan
ZSZhuowen Sun
Zhuowen Sun
YZYinpen Zhao
Yinpen Zhao
BRBo Ren
Bo Ren
QZQian Zhang
Qian Zhang

19 June 2018 in Journal of Testing and Evaluation
Verified
Journal Article
Closed access
XHXianjie Hao
Xianjie Hao
LYLiang Yuan
Liang Yuan
JXJun-Hua Xue
Jun-Hua Xue
SWShao-hua Wang
Shao-hua Wang
BRBo Ren
Bo Ren
YLYu-Lin Li
Yu-Lin Li
The stability of an underground tunnel is closely related to its stress path. Here, a total of twelve load levels with three load paths are designed to analyze the influence of magnitude and path of stress on the stability of an underground tunnel from the perspective of tunnel displacement characteristics, stress distribution, and crack propagation by physical model testing and numerical simulation. The results show that the cracks are generated from the corner of the sidewall first by the vertical maximum principal stress; the larger the initial loading, the higher the initial crack position in the sidewalls of the tunnel, and the tendency of the cracking to converge to the arch foot is also more obvious. As the applied pressure increases, the average length and depth of cracking of the sidewall, the radial strain, and the circumferential strain all undergo an exponential increase; the average length grows faster than the depth, and the growth in radial strain is faster than that of the circumferential strain. When tunnels with different loading paths are subjected to the same applied pressure, and if the load rate is low because of progressive damage, it leads to damage at greater depths, but the displacements are relatively small. On the contrary, when the load rate is rapid, under the effect of a certain dynamic load, the damage is more severe, and the displacements are larger; but, because the load is borne by the entire model, the depth of the damage is relatively small. It is important to note that the effect of the stress path applies only within certain stress magnitudes. With increasing stress, the effect of the stress path diminishes.

22 May 2017 in Geotechnical and Geological Engineering
Verified
Journal Article
Closed access
PDF file
XHXianjie Hao
Xianjie Hao
LYLiang Yuan
Liang Yuan
YZYixin Zhao
Yixin Zhao

25 March 2019 in Advances in Materials Science and Engineering
Verified
Journal Article
Open access
XHXianjie Hao
Xianjie Hao
QXQuansheng Xu
Quansheng Xu
DYDequan Yang
Dequan Yang
SWShao-hua Wang
Shao-hua Wang
YWYingnan Wei
Yingnan Wei
Brittleness is one of the most significant properties of geomaterials. However, very few studies have been conducted on factors influencing the rock brittleness indices. In this paper, conventional triaxial compression tests were carried out to investigate the effects of confining pressure and bedding angle on the brittleness of slate. From the perspective of energy, brittleness is an index that could reflect the release rate of energy that accumulated in the slate under the effect of external energy after reaching peak strength. Therefore, a new brittleness index of slate based on postpeak energy release is proposed herein. The applicability of this index is illustrated by comparing with other five existing brittleness indices. The following results can be obtained. (1) The confining pressure exerts a great influence on the brittleness of slate. With the increase of confining pressure, the brittleness of slate decreases significantly. The dispersion of brittleness values of slate declines with increasing confining pressure. (2) There is a parabolic relationship between slate brittleness and bedding angle. As bedding angle increases, the brittleness is intensified and reaches its maximum at a bedding angle of about 45° and then decreases gradually. (3) In contrast to the previous indices, the brittleness index proposed in this paper can describe the whole process of the postpeak stage through an index of the energy release, which makes this measure more suitable for rock that has the characteristics of step-drop or bench-drop at the postpeak stage.

1 January 2019 in Advances in Civil Engineering
Verified
Journal Article
Open access
PDF file
XHXianjie Hao
Xianjie Hao
SWShao-hua Wang
Shao-hua Wang
DJDuoxiang Jin
Duoxiang Jin
BRBo Ren
Bo Ren
XZXiangyang Zhang
Xiangyang Zhang
YFYingjie Fan
Yingjie Fan
The process of crack propagation and tunnel failure is affected by the cross‐sectional geometry of an underground tunnel. In order to quantify the effect of section shape on the process of crack propagation in deep tunnels under high ground stress conditions, a total of four physical models with two cross‐sectional shapes and twelve stress levels were designed and several large‐scale physical model tests were conducted. The results indicated that, when the vertical stress is 4.94 MPa, the length and depth of the cracks generated in the rock surrounding the horseshoe tunnel are about eight times that around a circular tunnel. The position where the circumferential displacement of the horseshoe tunnel begins to be stable is about two, to two and a half, times that around a circular tunnel. After the deep chamber was excavated, continuous spalling was found to occur at the foot of the horseshoe tunnel and microcracks in the surrounding rock were initially generated from the foot of the side wall and then developed upwards to form a conjugate sliding shape to the foot of the arch roof, where the cracks finally coalesced. Discontinuous spalling occurred at the midheight of the side wall of the circular tunnel after excavation, and microcracks in the surrounding rock were initially generated from the midheight of the side wall and then extended concentrically to greater depth in the rock mass surrounding the tunnel. Tensile failure mainly occurred on the surface of the side wall: shear failure mainly appeared in the surrounding rock.