The stability of an underground tunnel is closely related to its stress path. Here, a total of twelve load levels with three load paths are designed to analyze the influence of magnitude and path of stress on the stability of an underground tunnel from the perspective of tunnel displacement characteristics, stress distribution, and crack propagation by physical model testing and numerical simulation. The results show that the cracks are generated from the corner of the sidewall first by the vertical maximum principal stress; the larger the initial loading, the higher the initial crack position in the sidewalls of the tunnel, and the tendency of the cracking to converge to the arch foot is also more obvious. As the applied pressure increases, the average length and depth of cracking of the sidewall, the radial strain, and the circumferential strain all undergo an exponential increase; the average length grows faster than the depth, and the growth in radial strain is faster than that of the circumferential strain. When tunnels with different loading paths are subjected to the same applied pressure, and if the load rate is low because of progressive damage, it leads to damage at greater depths, but the displacements are relatively small. On the contrary, when the load rate is rapid, under the effect of a certain dynamic load, the damage is more severe, and the displacements are larger; but, because the load is borne by the entire model, the depth of the damage is relatively small. It is important to note that the effect of the stress path applies only within certain stress magnitudes. With increasing stress, the effect of the stress path diminishes.
Brittleness is one of the most significant properties of geomaterials. However, very few studies have been conducted on factors influencing the rock brittleness indices. In this paper, conventional triaxial compression tests were carried out to investigate the effects of confining pressure and bedding angle on the brittleness of slate. From the perspective of energy, brittleness is an index that could reflect the release rate of energy that accumulated in the slate under the effect of external energy after reaching peak strength. Therefore, a new brittleness index of slate based on postpeak energy release is proposed herein. The applicability of this index is illustrated by comparing with other five existing brittleness indices. The following results can be obtained. (1) The confining pressure exerts a great influence on the brittleness of slate. With the increase of confining pressure, the brittleness of slate decreases significantly. The dispersion of brittleness values of slate declines with increasing confining pressure. (2) There is a parabolic relationship between slate brittleness and bedding angle. As bedding angle increases, the brittleness is intensified and reaches its maximum at a bedding angle of about 45° and then decreases gradually. (3) In contrast to the previous indices, the brittleness index proposed in this paper can describe the whole process of the postpeak stage through an index of the energy release, which makes this measure more suitable for rock that has the characteristics of step-drop or bench-drop at the postpeak stage.
The process of crack propagation and tunnel failure is affected by the cross‐sectional geometry of an underground tunnel. In order to quantify the effect of section shape on the process of crack propagation in deep tunnels under high ground stress conditions, a total of four physical models with two cross‐sectional shapes and twelve stress levels were designed and several large‐scale physical model tests were conducted. The results indicated that, when the vertical stress is 4.94 MPa, the length and depth of the cracks generated in the rock surrounding the horseshoe tunnel are about eight times that around a circular tunnel. The position where the circumferential displacement of the horseshoe tunnel begins to be stable is about two, to two and a half, times that around a circular tunnel. After the deep chamber was excavated, continuous spalling was found to occur at the foot of the horseshoe tunnel and microcracks in the surrounding rock were initially generated from the foot of the side wall and then developed upwards to form a conjugate sliding shape to the foot of the arch roof, where the cracks finally coalesced. Discontinuous spalling occurred at the midheight of the side wall of the circular tunnel after excavation, and microcracks in the surrounding rock were initially generated from the midheight of the side wall and then extended concentrically to greater depth in the rock mass surrounding the tunnel. Tensile failure mainly occurred on the surface of the side wall: shear failure mainly appeared in the surrounding rock.
Fiber Metal Laminates (FMLs) such as GLARE and CARALL being light weight, strong and having high fatigue resistance are widely used in manufacturing of large aerospace/automobile parts. These parts/structures generally have larger radius profile curves and simpler design such as aircraft fuselage or flap skins etc and usually processed by autoclave molding techniques which have very long process time. Due to lengthy process time of such processes or tendency of fracture of layered/bonded structure if traditional sheet forming techniques are used, FMLs have not been considered for fabrication of parts with relatively smaller diameters and more complex shapes. This study attempts and investigates a new methodology to form relatively smaller and complicated parts using traditional sheet metal forming technique. Two Aluminum (Al-2024) layers each 0.8 mm thick are used as outer layers and a flexible Silicone rubber sheet with 1 mm thickness is used as core layer during forming. Gap between die & binder and shape as well as size of blanks have been considered as important process variables for a punch displacement upto 40 mm. Effect of presence of rubber sheet on forming of Al is also studied in details. The results show that die-binder gap and blank holding force are most critical factors which effect formability. The final product showed wrinkles due to presence of rubber sheet. The new method is very efficient to produce hybrid parts made of metal-composite materials. Future work has been suggested to further optimize the process, material and part quality. This study will expand the application areas of metal forming and will open new avenues for the experts working on weight, strength, vibrations and heat transfer areas for future research.