Three donor–acceptor (D–A)-structured conjugated polymers with different backbones, poly((9,9-dioctylfluorene)-2,7-diyl-alt-benzothiadiazole) (F8BT), poly((9,9-dioctylfluorene)-2,7-diyl-alt-(4,7-bis(3-hexylthien-5-yl)-2,1,3-benzothiadiazole)-2′,2′′-diyl) (F8TBT), and poly(N-9′-heptadecanyl-2,7-carbazole-alt-(4,7-bis(3-hexylthien-5-yl)-2,1,3-benzothiadiazole)-2′,2′′-diyl) (C8TBT), were synthesized via conventional Suzuki polymerization. All three polymers showed good thermal and electrochemical stabilities. The UV-vis absorption spectra indicated that the introduction of thiophene units into the polymer backbone decreased the bandgap of the polymers. When the three polymer films were doped with FeCl3, different thermoelectric properties were observed. F8TBT and C8TBT, which contained thiophene units, showed a higher electrical conductivity than F8BT. As the temperature increased, C8TBT exhibited the highest Seebeck coefficient of 335 μV K−1 at 90 °C and a maximum power factor of 13.11 μW m−1 K−2. These results demonstrated that the polymer backbone structure greatly influences the thermoelectric properties and the inclusion of thiophene and carbazole units can effectively improve the thermoelectric properties. Therefore, this work is a novel and important reference to design and synthesize high-performance thermoelectric conjugated polymers.
With the good planarity of conjugated backbones and high carrier mobilities, two-dimensional conjugated benzodithiophene (BDT)-based polymers find great potential in renewable energy conversion and storage. In this work, two BDT-based alternative copolymers, P(BDT-EDOT) and two-dimensional conjugated P(BDTTT-EDOT), are designed and synthesized to systematically investigate the influence of two-dimensional conjugated structures on the thermoelectric performance of conjugated polymers. Compared with P(BDT-EDOT) films, the larger Seebeck coefficient of doped P(BDTTT-EDOT) films (115.58 μV K−1) can be attributed to the enhancement of the density of states around the Fermi level, which is proved by the ultraviolet photoemission spectroscopy measurement and Mott parameters calculation. The electrical conductivities of doped P(BDTTT-EDOT) films are gradually decreased with the increasing temperature, and a large Seebeck coefficient above 800 μV K−1 is achieved at 350 K, indicating their semi-metallic behavior. The power factor of doped P(BDTTT-EDOT) films can reach 101.3 μW m−1 K−2 at 350 K, which is more than 100 times higher than that of the P(BDT-EDOT) film (0.9 μW m−1 K−2) at 350 K.
Here, we present a rational strategy for a wide-range of predictable tuning methods for the elastic modulus (G′) of alkylated π-conjugated polymers (Alk-CPs). Alk-CPs and their blends exhibit consistent emission chromaticities despite a drastic change in G′, which would help in the straightforward design of future optoelectronically active soft materials.
Three benzo[1,2-b:4,5-b′]dithiophene (BDT)-based donor–acceptor (D–A) conjugated polymers with different side chains were designed, synthesized, and investigated as organic thermoelectric materials. Changing the side chains caused the three polymers to have different physical and chemical properties. The thermoelectric properties of BDT-based conjugated polymers have been systematically investigated through fine tuning of the side chains. Among the three polymers, the polymer with alkylthienothiophene moieties as the side chains exhibited the best thermal stability (thermal decomposition temperature above 400 °C), the highest electrical conductivity (1.519 S cm−1), and the largest Seebeck coefficient (413.79 μV K−1). The results of this study can guide the future design and synthesis of high-performance thermoelectric conjugated polymers.