Biphenyl phthalonitrile (BPh) resins with good thermal and thermo-oxidative stability demonstrate great application potential in aerospace and national defense industries. However, BPh monomer has a high melting point, poor solubility, slow curing speed and high curing temperature. It is difficult to control the polymerization process to obtain the resins with high performance. Here, a BPh prepolymer (BPh-Q) was prepared by reacting 1,7-bis(hydroxymethyl)-m-carborane (QCB) with BPh monomers. The BPh-Q exhibited much better solubility, faster curing speed and lower curing temperature compared with pure BPh and BPh modified with bisphenol A (BPh-B, a common prepolymer of BPh). Thus, the polymerization process of BPh was greatly accelerated at a low temperature, resulting in a BPh resin with enhanced thermostability and oxidation resistance. The experimental and theoretical models revealed the promotion effect of B-H bond on the curing reaction of phthalonitrile via Markovnikov addition reaction due to the special steric structure of carborane. This study provided an efficient method to obtain low-temperature curing phthalonitrile resins with high thermal and thermo-oxidative resistance, which would be potentially useful for the preparation of high-performance cyanide resin-based composites.
A novel antifouling polyethersulfone (PES) hollow fiber membrane was modified by the addition of bisphenol sulfuric acid (BPA-PS) using a reverse thermally induced phase separation (RTIPS) process. BPA-PS was synthesized by click chemistry and was blended to improve the hydrophilicity of PES hollow fiber membranes. The performance of PES/BPA-PS hollow fiber membranes, prepared with different contents of BPA-PS and at different temperatures of the coagulation water bath, was characterized by scanning electron microscopy (SEM), pure water flux (Jw), BSA rejection rate (R), atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR) and water contact angle measurements. SEM morphologies revealed that a finger-like cross-section emerged in the hollow fiber membrane by a non-solvent induced phase separation (NIPS) mechanism while a sponge-like cross-section appeared in the hollow fiber membrane via the RTIPS method. Both FTIR and XPS analysis indicated that the sulfate group in BPA-PS was successfully blended with the PES membranes. The results from AFM and water contact angle measurements showed that the surface roughness increased and the hydrophilicity of the PES/BPA-PS hollow fiber membrane was improved with the addition of BPA-PS. The results demonstrated that the PES/BPA-PS membrane with 1 wt% BPA-PS via RTIPS exhibited optimal properties.
A homologous series of hyperbranched polyesters (HBPEs) was successfully synthesized via an esterification reaction of 2,2-bis(methylol)propionic acid (bis-MPA) with pentaerythritol. The molecular weights of the HBPEs were 2160, 2660, 4150 and 5840 g/mol, respectively. These HBPEs were used as additives to prepare polysulfone (PSf) hollow fiber membranes via non-solvent induced phase separation. The characteristic behaviors of the casting solution were investigated, as well as the morphologies, hydrophilicity and mechanical properties of the PSf membranes. The results showed that the initial viscosities of the casting solutions were increased, and the shear-thinning phenomenon became increasingly obvious. The demixing rate first increased and then decreased when increasing the HBPE molecular weight, and the turning point was 2660 g/mol. The PSf hollow fiber membranes with different molecular weights of HBPEs had a co-existing morphology of double finger-like and sponge-like structures. The starting pure water contact angle decreased obviously, and the mechanical properties improved.
2 January 2020 in International Journal of Smart and Nano Materials
Silicone foams with and without liquid fillers (silicone oils of various types and glycerol, respectively) are synthesized and analyzed to be used as dielectric layers in capacitive sensors. A simple fabrication technique involving only four components i.e. Sylgard 184, glycerol, sodium hydroxide and ethanol is used to make these silicone foams after which they are filled with silicone oil or glycerol by soaking the foam in respective liquid. Mechanical and dielectric properties of the foams are examined. The oil reinforces the foam’s dielectric properties, softens the foam and improves its capacitive response, making it a very good dielectric material for fabricating capacitive pressure sensors. Compared to dry silicone foams, foams filled with – and swollen by – chloropropyl-functional silicone oil, show a low Young’s modulus (31 kPa), a high and stable relative dielectric permittivity of around 5, and a high capacitive response of 132% for an applied pressure of 12 kPa. The presence of oil stabilizes the soft foam and ensures that it does not buckle under high pressure. Graphical abstract
Sulfonated polyethersulfone (SPES) was used as an additive to prepare hydrophilic poly(ethersulfone) (PES) hollow fiber membranes via non-solvent assisted reverse thermally induced phase separation (RTIPS) process. The PES/SPES/N,N-dimethylacetamide (DMAc)/ polyethylene glycol 200 (PEG200) casting solutions are lower critical solution temperature (LCST) membrane forming systems. The LCST and phase separation rate increased with the increase of SPES concentrations, while the casting solutions showed shear thinning. When the membrane forming temperature was higher than the LCST, membrane formation mechanism was controlled by non-solvent assisted RTIPS process and the also membranes presented a more porous structure on the surface and a bi-continuous structure on the cross section. The membranes prepared by applying SPES present higher pure water flux than that of the pure PES membrane. The advantages of the SPES additive are reflected by the relatively high flux, good hydrophilicity and excellent mechanical properties at 0.5 wt.% SPES content.