JianFeng Dai

Prof. JianFeng Dai

School of Science, Lanzhou University of Technology

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 June 2014 in Discover Nano
Verified
Journal Article
Open access
PDF file
TXTao Xian
Tao Xian
HYHua Yang
Hua Yang
LDLijing Di
Lijing Di
JMJinyuan Ma
Jinyuan Ma
HZHaimin Zhang
Haimin Zhang
JDJianFeng Dai
JianFeng Dai
SrTiO3-graphene nanocomposites were prepared via photocatalytic reduction of graphene oxide by UV light-irradiated SrTiO3 nanoparticles. Fourier transformed infrared spectroscopy analysis indicates that graphene oxide is reduced into graphene. Transmission electron microscope observation shows that SrTiO3 nanoparticles are well assembled onto graphene sheets. The photocatalytic activity of as-prepared SrTiO3-graphene composites was evaluated by the degradation of acid orange 7 (AO7) under a 254-nm UV irradiation, revealing that the composites exhibit significantly enhanced photocatalytic activity compared to the bare SrTiO3 nanoparticles. This can be explained by the fact that photogenerated electrons are captured by graphene, leading to an increased separation and availability of electrons and holes for the photocatalytic reaction. Hydroxyl (·OH) radicals were detected by the photoluminescence technique using terephthalic acid as a probe molecule and were found to be produced over the irradiated SrTiO3 nanoparticles and SrTiO3-graphene composites; especially, an enhanced yield is observed for the latter. The influence of ethanol, KI, and N2 on the photocatalytic efficiency was also investigated. Based on the experimental results, ·OH, h+, and H2O2 are suggested to be the main active species in the photocatalytic degradation of AO7 by SrTiO3-graphene composites. PACS 61.46. + w; 78.67.Bf; 78.66.Sq

1 February 2021 in Materials Research Express
Verified
Journal Article
Open access
PDF file
SGShanshan Gao
Shanshan Gao
WLWeixue Li
Weixue Li
JDJianFeng Dai
JianFeng Dai
QWQing Wang
Qing Wang
ZSZhongqiang Suo
Zhongqiang Suo
The effects of transition metal (Sc, Ti, V, Cr, Mn, Fe, Co, Ni, Cu, and Zn) doping on the stability, electronic structure and optical properties of β-Ga2O3 have been studied using GGA and GGA + U. The results show that the U value can correct the strong interaction of the d-layer, causing orbital hybridization and affecting the position and number of impurity energy levels. It can move the conduction band to higher energy levels and weaken the role of Ga-3p in the valence band. The Ti-doped β-Ga2O3 is easily formed, followed by V, Cr, Sc, Fe, Mn, Co, Ni, Cu, and Zn doping. Some bands change regularly with the increase of atomic number. All systems become degraded semiconductors after doping. All doping will make the β-Ga2O3 red shift. Among them, the absorption intensity of Cu doping in the visible light range is significantly improved.

14 February 2019 in Materials
Verified
Journal Article
Open access
PDF file
JDJianFeng Dai
JianFeng Dai
SXShangbin Xi
Shangbin Xi
DLDongna Li
Dongna Li
A multi-physics coupling numerical model of the curing process is proposed for the thermosetting resin composites in this paper, and the modified “cure hardening instantaneously linear elastic (CHILE)” model and viscoelastic model are adopted to forecast residual stress and deformation during the curing process. The thermophysical properties of both models are evolved in line with temperature and degree of cure (DOC). Accordingly, the numerical simulation results are improved to be more accurate. Additionally, the elastic modulus of the materials is calibrated to be equal to the modulus of viscoelastic relaxation by a defined function of time in the CHILE model. Subsequently, this work effectuates the two proposed models in a three-dimensional composite laminate structure. Through comparing the two numerical outcomes, it is customary that the residual stress and deformation acquired by the modified model of CHILE conform to those ones assessed through adopting the viscoelastic model.

1 August 2020 in Materials Research Express
Verified
Journal Article
Open access
PDF file
ZLZengpeng Li
Zengpeng Li
JDJianFeng Dai
JianFeng Dai
CCChen Cheng
Chen Cheng
ZSZhongqiang Suo
Zhongqiang Suo
WQWang Qing
Wang Qing
Chromium (Cr) doped cobalt ferrite (Co1−xCrxFe2O4:x = 0.0, 0.02, 0.04, 0.06, 0.08, 0.1, denoted as to CCFO) hollow nanotubes were synthesized by electrospinnig method followed by, calcining treatment at 700 °C in air. The samples exhibited a single phase cubic spinel phase. The lattice constant of the samples was found to initially decreased and thereafter increases with increased of Cr content. The morphology analysis indicated that the samples displayed a disordered arrangements of hollow structures and the relevant surfaces were rough and porous. Transmission electron microscopy (TEM) paragraph confirmed that the doped CCFO nanotubes had a polycrystalline nature and exhibited the changes in the corresponding crystal structure. X-ray photoelectron spectroscopy (XPS) confirmed that Cr doping affect the crystal structure and atomic-binding energy. The analysis of magnetic hysteresis loop indicated an obvious reduction in the saturation magnetization (Ms) of cobalt ferrite with increasing in Cr substitution. The remanent magnetization (Mr) and coercivity were increased at first and then decreased with increasing of Cr content, which was elucidated by the surface effect and magnetic moment direction. The switching field distribution analysis indicated the magnetically crystal soft phase and there were multiple-step processes to reach magnetic reversal.

1 September 2020 in Materials
Verified
Journal Article
Open access
PDF file
CCChen Cheng
Chen Cheng
JDJianFeng Dai
JianFeng Dai
ZLZengpeng Li
Zengpeng Li
WFWei Feng
Wei Feng
The morphology of magnetic materials has a great influence on the properties, which is attributed to the magnetic anisotropy of the materials. Therefore, it is worth studying the fabrication of the aligned fiber and the change of its domain distribution. Nanoparticles and nanofibers were prepared by the hydrothermal and electrospinning methods, respectively. At the same time, the arranged nanofibers were collected by the drum collecting device. After the same annealing at 700 °C, it was found that the diameter of fibers collected by different collecting drums is similar. By studying the hysteresis loops of nanoarrays, it was found that they had strong anisotropy. The easy axis was parallel to the long axis, the Hc and Mr of the easy axis and the hard axis were 1330.5 Oe, 32.39 Am2/kg, and 857.2 Oe, 24.8 Am2/kg, respectively. Due to the anisotropy of the shape and the interaction between the particles, the Hc could not be enhanced. Therefore, the Ms and Hc of the nanoparticles were 80.23 Am2/kg and 979.3 Oe, respectively. The hysteresis loop and the change of magnetic moment during the demagnetization of the CoFe2O4 nanofiber array were simulated via micromagnetic software. The simulated Hc was 1480 Oe, which was similar to the experimental value.

1 January 2020 in Materials Research Express
Verified
Journal Article
Open access
QWQing Wang
Qing Wang
HGHaoran Gao
Haoran Gao
XQXuefeng Qin
Xuefeng Qin
JDJianFeng Dai
JianFeng Dai
WLWeixue Li
Weixue Li
NiFe2O4@CoFe2O4 core–shell nanofibers were prepared by the co-electrospinning method. The prepared core–shell NiFe2O4@CoFe2O4 nanofibers electrode has the specific capacitance of 480 Fg−1 at a current density of 1Ag−1. After being cycled 2000 times at a current density of 5Ag−1, the capacity of NiFe2O4@CoFe2O4 core–shell nanofibers remained 87%. The electrochemical performance of the supercapacitor is improved by the synergistic action of the multi-metal and indicates that core/shell NiFe2O4@CoFe2O4 nanofibers are promising materials.