Chunming Zou

Chunming Zou


Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 June 2019 in Materials
Verified
Journal Article
Open access
PDF file
BGBo Gao
Bo Gao
YSYanfei Sui
Yanfei Sui
HWHongwei Wang
Hongwei Wang
CZChunming Zou
Chunming Zou
ZWZunjie Wei
Zunjie Wei
YSYanle Sun
Yanle Sun
In this work, the microstructure and solidification behavior of nickel-based superalloy GTD222 at different cooling rates are studied. The solidification of the superalloy GTD222 proceeds as follows: L → L + γ, L → L + γ + MC, L → L + (γ/γ′)-Eutectic and L → η phase. Due to alloying element redistribution, the temperature of the solidus GTD222 superalloy, 1310 °C, is slightly lower than the temperature of the liquidus, which is 1360 °C. It was found that the dendrite arm spacing of the alloy decreased with the increase of the cooling rate from 200 μm at 2.5 K/min to 100 μm at 20 K/min.

20 June 2021 in Crystals
Verified
Journal Article
Open access
PDF file
RZrong zhang
rong zhang
CZChunming Zou
Chunming Zou
ZWZunjie Wei
Zunjie Wei
HWHongwei Wang
Hongwei Wang
The microstructure of the Si phase in Al-20Si alloys solidified under high pressure was investigated. The results demonstrate that the morphology of Si phase transformed (bulk→short rod→long needle) with the increase of superheat temperature under high pressure. At a pressure of 3 GPa and a superheat temperature of 100 K, a microstructure with a uniform distribution of fine Si phases on the α-Al matrix was obtained in the Al-20Si alloy. In addition, a mathematical model was developed to analyze the spacing variation of the lamellar Al-Si eutectics under the effect of pressure. The lamellar Al-Si eutectics appeared at 2 GPa and superheat temperatures of 70–150 K, and at 3 GPa and superheat temperatures of 140–200 K. With the increase of pressure from 2 GPa to 3 GPa, the average spacing of lamellar Al-Si eutectics decreased from 1.2–1.6 μm to 0.9–1.1 μm. In binary alloys, the effect of pressure on the eutectic spacing is related to the volume change of the solute phase from liquid to solid. When the volume change of the solute phase from liquid to solid is negative, the lamellar eutectic spacing decreases with increasing pressure. When it is positive, the eutectic spacing increases with increasing pressure.

11 June 2023 in Materials
Verified
Journal Article
Open access
PDF file
RZrong zhang
rong zhang
CZChunming Zou
Chunming Zou
ZWZunjie Wei
Zunjie Wei
HWHongwei Wang
Hongwei Wang
The microstructure and mechanical properties of SiC/Al-40Si composites prepared under high pressure were studied. As the pressure increases from 1 atm to 3 GPa, the primary Si phase in the Al-40Si alloy is refined. With increasing pressure, the composition of the eutectic point increases, the solute diffusion coefficient decreases exponentially, and the concentration of Si solute at the front of the solid–liquid interface of the primary Si is low, which contributes to the refining of the primary Si and inhibiting its faceted growth. The bending strength of SiC/Al-40Si composite prepared under 3 GPa was 334 MPa, which was 66% higher compared to the Al-40Si alloy prepared under the same pressure.

8 May 2019 in Preprints.org
Verified
Preprint
Open access
PDF file
BGBo Gao
Bo Gao
YSYanfei Sui
Yanfei Sui
HWHongwei Wang
Hongwei Wang
CZChunming Zou
Chunming Zou
ZWZunjie Wei
Zunjie Wei
YSYanle Sun
Yanle Sun
The microstructure and solidification behavior of nickel based GTD222 superalloy at different cooling rates are studied. The solidification of the GTD222 superalloy proceeds as follows: L→L+γ, L→L+γ+MC, L→L+(γ/γ ′)-Eutectic and L→η phase. The temperature of liquidus of GTD222 superalloy is 1360 °C while the solidus is slightly lower at 1310 °C, which due to the alloying elements redistribution. It was found that the dendrite arm spacing of the alloy decreased with the increase of cooling rate (From 200 μm at 2.5 K/min to 100 μm at 20 K/min).

1 November 2016 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
CZChunming Zou
Chunming Zou
WJWei Jiang
Wei Jiang
HWHongwei Wang
Hongwei Wang
ZHZhonglue Hu
Zhonglue Hu
ZWZunjie Wei
Zunjie Wei

9 June 2023 in Materials
Verified
Journal Article
Open access
PDF file
RZrong zhang
rong zhang
CZChunming Zou
Chunming Zou
ZWZunjie Wei
Zunjie Wei
HWHongwei Wang
Hongwei Wang
CLChuang Liu
Chuang Liu
The formation of coarse primary Si is the main scientific challenge faced in the preparation of high-Si Al matrix composites. The SiC/Al-50Si composites are prepared by high pressure solidification, which allows the primary Si to form a SiC–Si spherical microstructure with SiC, while the solubility of Si in Al is increased by high pressure to reduce the proportion of primary Si, thus enhancing the strength of the composites. The results show that the high melt viscosity under high pressure makes the SiC particles almost “fixed” in situ. The SEM analysis shows that the presence of SiC in the growth front of the primary Si will hinder its continued growth and eventually form SiC–Si spherical microstructure. Through aging treatment, a large number of dispersed nanoscale Si phases are precipitated in the α-Al supersaturated solid solution. The TEM analysis shows that a semi-coherent interface is formed between the α-Al matrix and the nanoscale Si precipitates. The three-point bending tests shows that the bending strength of the aged SiC/Al-50Si composites prepared at 3 GPa is 387.6 MPa, which is 18.6% higher than that of the unaged composites.