Antonino Cataldo

Dr. Antonino Cataldo

Marche Polytechnic University, Department of Information Engineering; INFN- National Laboratory of Frascati
orcid

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 June 2015 in IEEE Transactions on Microwave Theory and Techniques
Verified
Journal Article
Closed access
LPLuca Pierantoni
Luca Pierantoni
DMDavide Mencarelli
Davide Mencarelli
Maurizio BozziMaurizio Bozzi
Maurizio Bozzi
RMRiccardo Moro
Riccardo Moro
SMStefano Moscato
Stefano Moscato
Stefano BellucciStefano Bellucci
Stefano Bellucci
This paper presents the design and fabrication of a broadband microstrip attenuator, operating at 1-20 GHz, based on few layer graphene flakes. The RF performance of the attenuator has been analyzed in depth. In particular, the use of graphene as a variable resistor is discussed and experimentally characterized at microwave frequencies. The structure of the graphene-based attenuator integrates a micrometric layer of graphene flakes deposited on an air gap in a microstrip line. As highlighted in the experiments, the graphene film can range from being a discrete conductor to a highly resistive material, depending on the externally applied voltage. As experimental evidence, it is verified that the application of a proper voltage through two bias tees changes the surface resistivity of graphene, and induces a significant change of insertion loss of the microstrip attenuator.

1 June 2021 in Separation and Purification Technology
Verified
Journal Article
Closed access
VMValentina Macchioni
Valentina Macchioni
KCKatya Carbone
Katya Carbone
Antonino CataldoAntonino Cataldo
Antonino Cataldo
RFRoberta Fraschini
Roberta Fraschini
SBStefano Bellucci
Stefano Bellucci

22 June 2017 in IEEE Antennas and Wireless Propagation Letters
Verified
Journal Article
Closed access
Muhammad YasirMuhammad Yasir
Muhammad Yasir
Patrizia SaviPatrizia Savi
Patrizia Savi
SBSilvia Bistarelli
Silvia Bistarelli
Antonino CataldoAntonino Cataldo
Antonino Cataldo
Maurizio BozziMaurizio Bozzi
Maurizio Bozzi
SBStefano Bellucci
Stefano Bellucci
This letter presents a voltage-controlled tunable planar antenna based on few-layer graphene flakes. The antenna consists of a rectangular patch with a shorted microstrip stub connected to the radiating edge, and a graphene pad located at the input of the stub. The proposed design exploits the variation of the graphene resistance by an applied bias voltage. Without any bias voltage, the graphene pad behaves almost as an open circuit, not allowing any current passing and, thus, voiding the impact of the stub. Increasing the bias voltage reduces the graphene resistance, thus increasing the current passing through the pad into the stub. This results in the patch antenna radiating at a different frequency. A prototype operating at the frequency of 5 GHz has been designed and tested, demonstrating a frequency tunability larger than 10% with a limited gain degradation.

23 March 2017 in IEEE Microwave and Wireless Components Letters
Verified
Journal Article
Closed access
Muhammad YasirMuhammad Yasir
Muhammad Yasir
SBSilvia Bistarelli
Silvia Bistarelli
Antonino CataldoAntonino Cataldo
Antonino Cataldo
Maurizio BozziMaurizio Bozzi
Maurizio Bozzi
LPLuca Perregrini
Luca Perregrini
SBStefano Bellucci
Stefano Bellucci
This letter presents a voltage-controlled tunable attenuator based on few layer graphene flakes. The proposed structure exploits the variation of graphene resistance with an applied bias voltage. The attenuator consists of a microstrip line, connected to grounded metal vias through graphene pads: when no bias voltage is applied, the resistance of graphene is high and the pads behave as open circuits, causing minimum attenuation. By increasing the bias voltage, the resistance of the graphene pads decreases, connecting the metal vias to the microstrip, thus increasing the attenuation. A prototype operating in the frequency band from dc to 5 GHz has been designed and tested. The measured attenuation ranges from 0.3 to 15 dB at 3 GHz, with a bias voltage ranging from 0 (minimum attenuation) to 6.5 V (maximum attenuation).

22 October 2013 in Journal of Applied Physics
Verified
Journal Article
Open access
PDF file
Polina KuzhirPolina Kuzhir
Polina Kuzhir
APAlesia Paddubskaya
Alesia Paddubskaya
APA. Plyushch
A. Plyushch
NVN. Volynets
N. Volynets
SMSergey Maksimenko
Sergey Maksimenko
Lambin LambinLambin Lambin
Lambin Lambin
A comprehensive analysis of electrical, electromagnetic (EM), mechanical, and thermal properties of epoxy resin composites filled with 0.25–2.0 wt. % of carbon additives characterized by high surface area, both nano-sized, like carbon nanotubes (CNTs) and carbon black (CBH), and micro-sized exfoliated graphite (EG), was performed. We found that the physical properties of both CNTs- and CBH-based epoxy resin composites increased all together with filler content and even more clearly for CBH than for CNTs. In the case of EG-based composites, good correlation between properties and filler amount was observed for concentrations below 1.5 wt. %. We conclude that CBH and, to a lower extent, EG could replace expensive CNTs for producing effective EM materials in microwave and low-frequency ranges, which are, in addition, mechanically and thermally stable.

1 May 2016 in Composites Science and Technology
Verified
Journal Article
Closed access
APA. Plyushch
A. Plyushch
JMJ. Macutkevic
J. Macutkevic
Polina KuzhirPolina Kuzhir
Polina Kuzhir
JBJ. Banys
J. Banys
DBDz. Bychanok
Dz. Bychanok
SBS. Bellucci
S. Bellucci