Post-critical deformation states of composite thin-walled aircraft load-bearing structures

In aeronautical research experimental data sets of high quality are essential to verify and improve simulation algorithms. For this reason the experimental techniques need to be constantly refined. The shape, movement or deformation of structural aircraft elements can be measured implicitly in multiple ways; however, only optical, correlation-based techniques are able to deliver direct high-order and spatial results. In this paper two different optical metrologies are used for on-ground preparation and the actual execution of in-flight wing deformation measurements on a PW-6U glider. Firstly, the commercial PONTOS system is used for static tests on the ground and for wind tunnel investigations to successfully certify an experimental sensor pod mounted on top of the test bed fuselage. Secondly, a modification of the glider is necessary to implement the optical method named image pattern correlation technique (IPCT), which has been developed by the German Aerospace Center DLR. This scientific technology uses a stereoscopic camera set-up placed inside the experimental pod and a stochastic dot matrix applied to the area of interest on the glider wing to measure the deformation of the upper wing surface in-flight. The flight test installation, including the preparation, is described and results are presented briefly. Focussing on the compensation for typical error sources, the paper concludes with a recommended procedure to enhance the data processing for better results. Within the presented project IPCT has been developed and optimized for a new type of test bed. Adapted to the special requirements of the glider, the IPCT measurements were able to deliver a valuable wing deformation data base which now can be used to improve corresponding numerical models and simulations.

Flight testing is both vital for collecting data for aeronautic research and at the same time fascinating for its contributors. Taking a glider as a versatile test bed example, this paper presents a transnational measurement campaign within the framework of a collaborative project funded by the European Commission. This project Advanced In-Flight Measurement Techniques 2 (AIM²) is a follow-up of Advanced In-Flight Measurement Techniques (AIM) and dedicated to developing and enhancing promising optical metrology for various flight test applications up to an industrial level.The Image Pattern Correlation Technique (IPCT) and infrared thermography (IRT) are two of these modern non-intrusive measurement methods that were further developed and applied to the glider test bed within the scope of AIM². Focusing on optical deformation measurements with IPCT the experimental setup, the flight testing and results are summarily discussed. Gliders are not commonly used flight test platforms, which is why this contribution concludes with some lessons learned in general and especially related to the presented application. The experience to be shared with the flight testing community addresses equipment preparation, data collection and processing as well as how to meet official requirements and perform test flight operations in a dense controlled airspace.

The paper presents a methodology enabling the detection of aircraft touchdowns based on data obtained from accelerometers attached to the structural parts of the airframe in the cockpit or passenger compartment. Precise determination of the moment and place of touchdown of the main landing gear is challenging when analysing parameters such as height, flight speed and rate of descent. During the tests of the I-31T aircraft, it turned out that vibrations of the aircraft structure caused by the contact of the front and main landing gear with the ground have a repetitive character. In particular, this applies to longitudinal acceleration. The use of continuous wavelet analysis (CWT) allowed finding unique periodic features of the landing phenomenon that distinguish it from other forms of vibration occurring in individual flight phases. Ground and flight observations of experimental aeroplane MP-02 Czajka verified the proposed method of virtual touchdown detection. The results presented in this paper justify that this method may find broader application, especially for the light aircraft class.

Purpose: This paper aims to present the analysis of introduction of single engine turbo-prop aeroplane class in terms of certification specifications and flight crew licensing regulations. Design/methodology/approach: Following the results of flight testing and additional performance and sizing calculations, the proposed class was placed among the existing aeroplane taxonomy in terms of performance, flight loads, mass penalty, fuel economy and several other factors. Concerning small air transport initiative, the new class was tried to be placed as a starting point in commercial pilot career. Findings: The paper points the potential market for single engine turbopropeller aeroplanes and lists today obstacles in wider introduction. Therefore, remarks about required change of regulations and requirements for design process, as well as for crew licensing, are underlined. Practical implications: The results of the study would be helpful in preliminary design of a new low-power turboprop aeroplane, as well as during tailoring the certification specifications. Originality/value: The approach presented in this paper is a detailed extension of an original idea presented by author for the first time during Clean Sky/small air transport workshop.

This paper presents results of experimental and numerical analysis in terms of the finite element method of skin components of aircraft load bearing structures. The subject matter of the study was composite panels with stiffeners in the form of a regular grid of oriented longitudinal elements in...