A highly integrated 1.7-2.0 GHz digitally programmable frequency synthesizer using a MEMS resonator as its reference is presented. Due to the dimensions of the MEMS device (e.g., 25 mum by 114 mum), the entire system with a total area of 6.25 mm² can be housed in a small standard chip package. This considerably reduces the form factor and cost of the system, compared to using an external crystal as a reference. The MEMS resonators are clamped-clamped beams fabricated using a CMOS-compatible process. The main structural layer is made of silicon carbide, which provides the resonators with higher power handling capabilities and higher operating frequencies, compared to silicon. The resonators are electrostatically and thermally tunable - an 8.4% frequency tuning is demonstrated for a 9 MHz resonator. The 100 nm vertical transducer gaps of the resonators allow the use of electrostatic actuation voltages as low as 2 V. An integrated high gain-bandwidth trans-impedance amplifier (TIA) is combined with a resonator to generate the synthesizer's input reference signal. The TIA employs automatic gain control to mitigate the inherent low power handling capabilities and the non-linearities of the MEMS device, thus minimizing their effect on phase noise. The fractional- N synthesizer employs a 3rd-order 20-bit delta-sigma modulator to deliver a theoretical output resolution of ~ 11 Hz, in order to allow for high output frequency stability when used with an appropriate feedback loop. A fully integrated on-chip dual path loop filter is used to maintain a high level of system integration. With a supply voltage of 2 V, the phase noise for a 1.8 GHz output frequency and a ~12 MHz reference signal is -122 dBc/Hz at a 600 kHz offset, and -137 dBc/Hz at a 3 MHz offset.

The increasing air pollution across the globe has given rise to a global health crisis that is increasing at an alarming rate. Every year, millions of people lose their lives due to health risks caused by air pollutants. Hence, there is a pressing need for better solutions to accurately measure the amount of air pollution. This work is aimed at designing a highly compact, accurate, low-cost, self-resettable, and easy-to-use gravimetric-based particulate matter sensor solution for portable applications. Previous attempts have failed to realize true miniaturization, due to the size constraints of the virtual impactor needed—a mechanism that segregates the particulate matters based on their sizes. Our complete particulate matter sensor solution consists of three components (i) a piezoelectric resonating membrane, (ii) a virtual impactor, and (iii) a thermophoretic mechanism to reset the sensor. This paper presents a novel design of the virtual impactor, based on a folded configuration. This helps realize the entire system in a volume of 20 mm × 20 mm × 10 mm. We report here the design, working principles, fabrication, and experimental results of the virtual impactor.

This work introduces a novel architecture for increasing the sensitivity of bulk mode gyroscopes. It is based on adding parallel plate comb drives to the points of maximum vibration amplitude, and tuning the stiffness of the combs. This increases the drive strength and results in a significant sensitivity improvement. The architecture is targeted for technologies with ~100 nm transducer gaps in order to achieve very high performance devices. In this work, this sensitivity enhancement concept was implemented in SOIMUMPs, a commercial relatively large gap technology. Prototypes were measured to operate at frequencies of ~1.5 MHz, with quality factors of ~33,000, at a 10 mTorr vacuum level. Measurements using discrete electronics show a rate sensitivity of 0.31 μV/°/s, corresponding to a capacitance sensitivity of 0.43 aF/°/s/electrode, two orders of magnitude higher than a similar design without combs, fabricated in the same technology.

This article presents a 6.89 MHz MEMS oscillator based on an ultra-low-power, low-noise, tunable gain/duty-cycle transimpedance amplifier (TIA) and a bulk Lamé-mode MEMS resonator that has a quality factor (Q) of 3.24 × 10⁶. Self-cascoding and current-starving techniques are used in the TIA design to minimize the power consumption and tune the duty-cycle of the output signal. The TIA was designed and fabricated in TSMC 65 nm CMOS process technology. Its open-loop performance has been measured separately. It achieves a tunable gain between 107.9 dBΩ and 118.1 dBΩ while dissipating only 143 nW from a 1 V supply. The duty-cycle of the output waveform can be tuned from 23.25% to 79.03%. The TIA has been interfaced and wire bonded in a series-resonant oscillator configuration with the MEMS resonator and mounted in a small cavity standard package. The closed-loop performance of the whole oscillator has been experimentally measured. It exhibits a phase noise of −128.1 dBc/Hz and −133.7 dBc/Hz at 1 kHz and 1 MHz offsets, respectively.