In the last few years, the scientific community around the world has devoted a lot of attention to the search for the best methods of obtaining nanocellulose. In this work, nanocellulose was obtained in enzymatic reactions with strictly defined dispersion and structural parameters in order to use it as a filler for polymers. The controlled enzymatic hydrolysis of the polysaccharide was carried out in the presence of cellulolytic enzymes from microscopic fungi—Trichoderma reesei and Aspergillus sp. It has been shown that the efficiency of bioconversion of cellulose material depends on the type of enzymes used. The use of a complex of cellulases obtained from a fungus of the genus Trichoderma turned out to be an effective method of obtaining cellulose of nanometric dimensions with a very low polydispersity. The effect of cellulose enzymatic reactions was assessed using the technique of high-performance liquid chromatography coupled with a refractometric detector, X-ray diffraction, dynamic light scattering and Fourier transform infrared spectroscopy. In the second stage, polypropylene composites with nanometric cellulose were obtained by extrusion and injection. It was found by means of X-ray diffraction, hot stage optical microscopy and differential scanning calorimetry that nanocellulose had a significant effect on the supermolecular structure, nucleation activity and the course of phase transitions of the obtained polymer nanocomposites. Moreover, the obtained nanocomposites are characterized by very good strength properties. This paper describes for the first time that the obtained cellulose nanofillers with defined parameters can be used for the production of polymer composites with a strictly defined polymorphic structure, which in turn may influence future decision making about obtaining materials with controllable properties, e.g., high flexibility, enabling the thermoforming process of packaging.

Plant cell walls play an important role in shaping the defense strategies of plants. This research demonstrates the influence of two differentiators: the lifestyle and properties of the Trichoderma species on cell wall changes in common wheat seedlings. The methodologies used in this investigation include microscopy observations and immunodetection. In this study was shown that the plant cell wall was altered due to its interaction with Trichoderma. The accumulation of lignins and reorganization of pectin were observed. The immunocytochemistry indicated that low methyl-esterified pectins appeared in intercellular spaces. Moreover, it was found that the arabinogalactan protein epitope JIM14 can play a role in the interaction of wheat roots with both the tested Trichoderma strains. Nevertheless, we postulate that modifications, such as the appearance of lignins, rearrangement of low methyl-esterified pectins, and arabinogalactan proteins due to the interaction with Trichoderma show that tested strains can be potentially used in wheat seedlings protection to pathogens.

In the last decade, an increasingly common method of maize stover management is to use it for energy generation, including anaerobic digestion for biogas production. Therefore, the aim of this study was to provide a chemical and structural characterization of maize stover fractions and, based on these parameters, to evaluate the potential application of these fractions, including for biogas production. In the study, maize stover fractions, including cobs, husks, leaves and stalks, were used. The biomass samples were characterized by infrared spectroscopy (FTIR), X-ray diffraction and analysis of elemental composition. Among all maize stover fractions, stalks showed the highest C:N ratio, degree of crystallinity and cellulose and lignin contents. The high crystallinity index of stalks (38%) is associated with their high cellulose content (44.87%). FTIR analysis showed that the spectrum of maize stalks is characterized by the highest intensity of bands at 1512 cm⁻¹ and 1384 cm⁻¹, which are the characteristic bands of lignin and cellulose. Obtained results indicate that the maize stover fraction has an influence on the chemical and structural parameters. Moreover, presented results indicate that stalks are characterized by the most favorable chemical parameters for biogas production.

Nanocellulose has gained increasing attention during the past decade, which is related to its unique properties and wide application. In this paper, nanocellulose samples were produced via hydrolysis with ionic liquids (1-ethyl-3-methylimidazole acetate (EmimOAc) and 1-allyl-3-methylimidazolium chloride (AmimCl)) from microcrystalline celluloses (Avicel and Whatman) subjected to enzymatic pretreatment. The obtained material was characterized using Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), dynamic light scattering (DLS), scanning electron microscopy (SEM), and thermogravimetric analysis (TG). The results showed that the nanocellulose had a regular and spherical structure with diameters of 30–40 nm and exhibited lower crystallinity and thermal stability than the material obtained after hydrolysis with Trichoderma reesei enzymes. However, the enzyme-pretreated Avicel had a particle size of about 200 nm and a cellulose II structure. A two-step process involving enzyme pretreatment and hydrolysis with ionic liquids resulted in the production of nanocellulose. Moreover, the particle size of nanocellulose and its structure depend on the ionic liquid used.

Urea-formaldehyde adhesives are widely used in the wood-based materials industry. The study investigates the possibility of using cellulosic particles as a filler that modifies the properties of the resin and consequently improves the properties of plywood. Moreover, the study also examines the differences between microcellulose and nanocellulose used as a filler for UF adhesive. Based on the investigations, it was found that the addition of MFC and NCC significantly affected the curing process and rheological behaviour of adhesive mixtures. Modification led to increase of viscosity and extension of a gel time caused by lowering solid content of the resin. The experimental and reference plywood were tested in terms of bonding quality and mechanical properties such as modulus of elasticity and modulus of rigidity in accordance with applicable standards. The results of the tests confirmed that both the amount and the type of modifier added to the resin had a significant effect on the properties of plywood. The bonding quality and the above mentioned mechanical properties improved in all variants of modification; however the most effective was the addition of NCC in the amount of 10 %/100 g of solid resin. The slight decrease of formaldehyde emission was only observed for 5 % cellulosic particles added to 100 g of solid UF.