Aiming to reduce thermal energy loss at the cold side of a thermoelectric generator (TEG) module during thermoelectric conversion, a thermoelectric energy conversion system for heat recovery with a water-cooling energy exchange circuit was devised. The water-cooling energy exchange circuit realized sufficient recovery and reuse of heat accumulated at the cold side of the TEG, reduced the danger of heat accumulation, improved the stability and output capacity of thermoelectric conversion, and provided a low-cost and high-yield energy conversion strategy in energy conversion and utilization. Through the control variable method to adjust the heat generation of the heat source in the thermoelectric conversion, critical parameters (e.g., inner resistance of the TEG, temperatures of thermoelectric modules, temperature differences, output current, voltage, power, and efficiency of thermoelectric conversion) were analyzed and discussed. After using the control variable method to change the ratio of load resistance and internal resistance, the impacts of the ratio of load resistance to inner resistance of the TEG on the entire energy conversion process were elaborated. The results showed that the maximum value of output reached 397.47 mV with a current of 105.56 mA, power of 41.96 mW, and energy conversion efficiency of 1.16%. The power density of the TEG module is 26.225 W/m². The stability and practicality of the system with a water-cooling energy exchange circuit were demonstrated, providing an effective strategy for the recovery and utilization of heat energy loss in the thermoelectric conversion process.

In recent years, the need for reliable signal transmission in forested areas has increasingly grown, and the past few decades have witnessed significant developments in related research. With the emergence of smart forestry and precision forestry, understanding the science behind enhancing signal reliability in forests—specifically, studying the patterns and models of radio wave attenuation in these environments—has become crucial. To this end, we conducted a comprehensive review based on bibliometrics to summarize and construct the existing academic literature, revealing current research trends and hotspots. Utilizing bibliometric techniques, we analyzed the literature on radio wave attenuation in forests to summarize and evaluate previous studies. Our analysis indicates that empirical models (67%), hybrid models (21%), and equivalent models (12%) are the three main research clusters in this field. We observed that studies on radio attenuation are more prevalent in urban and artificial forests, while there is a scarcity of research in complex conditions like tropical rainforests and extreme weather; studies are more focused on UHF, VHF, and SHF frequency bands, with lesser attention given to other bands. Previous research has not adequately considered the impact of seasonal factors on signal attenuation patterns nor the influence of forest working environments.

Vibration harvesting is a promising method for walnut production owing to its low cost and high efficiency. However, current research focuses on simulation analysis and lacks a theoretical model explaining the walnuts’ specific vibration response. This affects the design of the input vibration parameters during harvesting and thus reduces the harvesting efficiency. In this paper, a novel theoretical model of walnuts during vibration harvesting was established to analyze the vibration response, including the motion morphology (motion trajectory and dropping position) and detachment force. A field test was then carried out to verify the theoretical model. The theoretical and experimental results showed that the motion trajectory of the walnuts during vibration harvesting is similar to an ellipse, and the dropping position is at either of the two end points of the trajectory. The detachment force was found to be proportional to the vibration amplitude and the square of the vibration frequency theoretically. This paper provides a theoretical reference for designing the optimal input vibration parameters of a harvesting device to improve the harvesting rate of walnuts.

A two-phase closed thermosyphon is an efficient heat transfer element. The heat transfer process of this type of thermosyphon includes conduction and convective heat transfer accompanied by phase changes. Variations in the inclination angle of a thermosyphon affect the steady-state heat transfer performance of the device. Therefore, the inclination angle is an important factor affecting the performance of a thermosyphon. In this paper, an equation for the actual heating area variations with respect to the inclination angle is deduced, and a model for the areal thermal resistance of a thermosyphon is proposed by analyzing the main influence mechanisms of the inclination angle on the heat transfer process. The experimental results show that the areal thermal resistance, which accounts for the effect of the actual heating area, does not change with respect to the inclination angle and exhibits a linear relationship with the heat transfer rate. The thermal resistance equation is fit according to the experimental data when the inclination angle of the thermosyphon is vertically oriented (90°), and the predicted values of the thermosyphon’s thermal resistance are obtained when the thermosyphon is inclined. The deviations between the experimental data and predicted values are less than ±0.05. Therefore, the theoretical equation can accurately predict the thermosyphon’s thermal resistance at different inclination angles.