Tip clearance flow in axial flow compressor is unavoidable and responsible for pressure losses and noise generation and influences the stability of the compressor. However, necessary flow measurement in the blade tip region is a great challenge due to the small gap width as well as the structure limitation. In this paper, a polyvinylidene fluoride (PVDF) piezoelectric-film sensor array is developed to capture the dynamic pressure field over the blade tip in an axial flow compressor. The PVDF sensor array with 40 evenly distributed sensing points is fabricated directly on a 30 μm thick aluminum-metalized polarized PVDF film through photolithography. Dynamic calibration of the sensor is accomplished using acoustic source as excitation and a microphone as a reference. The test pressure range is up to 3.5 kPa and the sampling frequency is 20 kHz. The sensor presents a high signal-to-noise ratio and good consistency with the reference microphone. Sensitivity, frequency response, linearity, hysteresis, repeatability as well as the influence of temperature are also investigated through the calibration apparatus. The calibration gives credence to the relevance and reliability of this sensor for the application in dynamic pressure field measurement. The sensor is then applied to an actual measurement in a compressor. The output of the PVDF sensor array is also compared with the results of common pressure transducers, and the features of the dynamic pressure filed are discussed. The results indicate that the PVDF sensor array is capable of the dynamic pressure field measurement over the blade tip, and superior to the conventional approaches in installation, spatial resolution, frequency response, and cost. These advantages indicate its potential broad application in pressure measurement, especially for the complex spatial surface or thin-walled structure, such as the blade surface and the thin casing wall of the compressor.
15 February 2005 in Journal of Engineering for Gas Turbines and Power
A nonlinear continuum damage mechanics model is proposed to assess the high temperature creep life of a steam turbine rotor, in which the effect of mean stress is taken into account and the damage is accumulated nonlinearly. The model is applied to a 300 MW steam turbine under hot start operation. The results are compared with those from the linear accumulation theory that is dominant in the creep life assessment of steam turbine rotors at present. The comparison results show that the nonlinear continuum damage mechanics model describes the accumulation and development of damage better than the linear accumulation theory.
12 December 2018 in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
Experimentation is an effective approach to study the dynamic coefficients of journal bearings because experimental results are more reliable than theoretical calculations. Dynamic coefficients identification based on the unbalance response is more easily implemented than other experimental methods because of its independence from external exciting devices. However, this method may involve an ill-conditioned matrix problem, which increases algorithm complexity and decreases the precision of identification results. In this paper, a novel method is proposed to avoid ill-posed problems in the coefficient identification of circular journal bearings based on the unbalance response. The main approach used to overcome the ill-conditioned matrix problem is the introduction of four complementary equations that are uncorrelated with the dynamic equations derived from the unbalance response. Two relational expressions between damping are deduced from the Reynolds equation, and the other two relations between stiffness are obtained from the Taylor expansion of static forces acting on journal bearings. With the use of the four complementary relations, the identification matrix has a low condition number, and the identification of circular journal bearing dynamic coefficients can be easily implemented. Numerical experiments on two-axial groove journal bearings are used to analyze the condition number and identification error as well as verify the efficacy and accuracy of this method. The results show that the proposed method has a good identification capability with high precision and low condition number in solving the identification problems of journal bearings.
It is well known that seal force has a great influence on dynamic coefficients of the rotor-seal system and Muszynska’s model is employed by many scholars to research the seal system. But the rotor-seal system has larger eccentricity ratio, Muszynska’s model will not describe the characteristics of the rotor-seal system well. So a more accurate model is critical for describing the seal force. An improved nonlinear model of a rotor-seal system is proposed for describing seal force of the rotor-seal system based on the two-control-volume model and rotor motion equation. This model can not only solve the larger eccentric problem but can also bring a simple calculation through the numerical methods. Dynamic coefficients of the rotor-seal system are also researched based on the new nonlinear model under the condition of the tooth-on-stator and tooth-on-rotor. In order to verify that the equation-control model is correct, Childs and Scharrer's experiment and two-control-volume model are employed and there is a comparison between theoretical results and experimental results. The result shows that theoretical results from the improved model are in better agreement with Childs and Scharrer's experiment than two-control-volume model. The proposed model in this paper provides a theoretic reference for further research on the rotor-seal system.
The position of fluid film in journal bearing will change while the journal moving in bearing, which can be named fluid film boundary migration (FFBM). It is usually ignored in the calculation of linear dynamic coefficients. While, the errors brought by this neglection was not ever investigated in detail. In this paper, the influence of FFBM on bearing dynamic coefficients and rotor system dynamic behaviors are investigated. A new perturbation-based model is proposed to take the FFBM into account by modifying the boundary conditions of governing equations. It is then verified by the experimental results and analytical results from previous research. Furthermore, the effects of FFBM on stiffness and damping in two typical journal bearings are investigated. The result indicates that the FFBM has a significant influence on dynamic coefficients of full circular journal bearing but little impact on journal bearing with axial grooves. Moreover, it affects the stiffness and damping more significantly in the cases of large length-to-diameter ratios or small eccentricity ratios in full circle bearing. Finally, the dynamical behavior of a rotor-bearing system with considering the FFBM is also investigated. The result shows that the FFBM of oil film has remarkable influences on the instability threshold and imbalance responses of the rotor system, which should not be ignored. The conclusions obtained in this research are expected to be helpful for the design of full circular journal bearings or rotor-bearing systems.