Ultra-short pulse laser interaction with diamond materials has attracted extensive interest in micro- and nano-machining, especially for the fabrication of micro tools, because of the straightforward method and high precision. Thanks to the development of chemical vapor deposition (CVD) technology, high-quality CVD diamonds are employed in more varieties of tools as performance-enhancing coatings. The purpose of the experiments reported here was to explore the machinability of CVD diamond coating under the irradiation of femtosecond (fs) pulsed laser. The factor-control approach was adopted to investigate the influence of scanning speed, single pulse energy and repetition rate on the surface quality and carbon phase transition of CVD diamond coating. The material removal rate and surface roughness were evaluated. The interaction mechanism of scanning speed, single pulse energy, and repetition rate were discussed, and the fs laser ablation threshold of CVD diamond coating was calculated. It was demonstrated that two ablation mechanisms (weak and intensive) were in existence as evidenced by the distinct surface morphologies induced under different processing conditions. A strong dependence on the variation of scanning speed and pulse energy is identified in the examination of surface roughness and removal rate. Lorentzian–Gaussian deconvolution of Raman spectra illustrates that fs laser irradiation yields a strong modification effect on the coating and release the compressive stress in it. Furthermore, a newly defined parameter referring to the fs laser energies applied to unit volume was introduced to depict the degree of ablation and the Taguchi method was used to figure out the significance of different parameters. The ablation threshold of CVD diamond coating at the effective pulses of 90 is calculated to be 0.138 J/cm2.
In order to study the microstructure and properties of stainless steel after laser surface remelting, based on the theory of laser surface remelting, a simulation model of nanosecond-pulsed laser surface remelted stainless steel was established to study the evolution law of the Marangoni force of the molten pool during laser surface remelting. A single-lane laser remelting experiment was performed to study the variation of the scanning speed on the remelting width, roughness, and layer microtopography. The “S” scanning path was used to remelt the stainless steel surface to investigate the bonding force between the remelted layer and the substrate, the hardness, microscopic morphology, and corrosion resistance. The results show that the viscosity of the liquid metal in the molten pool increases with the increase of the scanning speed. Larger liquid viscosity and smaller surface tension temperature gradients promote a weaker flow of liquid metal, which reduces the velocity of the liquid metal flow in the molten pool. With the increase of scanning speed, the remelting width gradually decreases, but the roughness gradually increases. When the element content of Cr increases, the element content of Fe and O decreases. The surface is covered with an oxide film, the main components of which are oxides of Cr and Fe, the remelted layer is greater than that of the substrate, and the corrosion resistance is improved. Laser surface remelting technology can improve the structure and properties of 304 stainless steel.
Liquid-assisted laser technology is used to etch defect-free materials for high-precision electronics and machinery. This study investigates water-jet-assisted laser etching of polysilicon material. The depths and widths of the etched grooves were investigated for different water-jet incident angles and velocities. To select optimal parameters for a composite etching processing, the results of many tests must be compared, and at least one set of good processing parameter combinations must be identified. Herein, the influence of different parameters on the processing results is studied using an orthogonal test method. The results demonstrate that the depths and widths of the processing grooves were nearly identical at water-jet angles of 30°and 60°; however, the 60° incidence conferred a slight advantage over 30° incidence. The section taper, section depth, and surface topography were optimized at a water-jet velocity of 24-m/s, 1.1-ms laser pulse width, 40-Hz frequency, and 180-A current. Under these conditions, the section taper and groove depth were 1.2° and 1.88 mm, respectively. The groove surfaces exhibited no splitting, slagging, or other defects, and no recast layers were visible.
To study the effects of aluminum alloys processed by a laser in air and water and at different water velocities, corresponding experiments were conducted and the impacting effects of different water velocities on the surface of the workpiece were simulated, respectively. The results show that when laser processing aluminum alloy materials in air, there is more slag and a recondensation layer on both sides of the groove, the heat-affected zone is larger and the surface processing quality is poor. When laser processing aluminum alloy materials in water, the processing quality is improved. With the increase in water velocity, the impacting and cooling effect is enhanced, the groove depth and groove width show a trend of first increasing and then decreasing, the slag and recondensation layer on both sides of the groove are reduced, the heat-affected zone is reduced and the processing quality of the groove is improved. When the water velocity reaches 30 m/s, a better groove can be obtained. Laser processing aluminum alloy materials in water can obtain better processing quality than laser processing in air.
A pitcher plant is a kind of liquid-infused porous surface that imparts an excellent directional manipulation ability to in-air droplets or underwater bubbles, so it has attracted researchers’ attention in both academic and industrial issues. In this work, a kind of liquid-infused anisotropic microgrooved slippery surface (LIAMSS) was fabricated through one-step femtosecond laser irradiation and lubricant coating technology. On the inclined LIAMSS, the underwater bubbles show great directional motion and anisotropic spreading ability under the effect of buoyancy. It should be noted that the interaction between the air and the lubricant layer plays a dominant role in determining the attachment and the movement of the underwater bubble, which could be ascribed to the competition between the adhesion resistance induced by contact angle hysteresis and the drive force induced by buoyancy. Additionally, the bubble shows obvious anisotropy on the LIAMSS with the increase in volume because of the restriction of the slippery area, and the bubble contact angle perpendicular to the grooved region is about 88○ when the bubble volume is 5 μL. We believe that the present findings would accelerate the application of this kind of bubble slippery surface in underwater gas collection and tail gas treatment.