LIU WEI

Dr. LIU WEI


Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 July 2021 in Applied Physics A
Verified
Journal Article
Closed access
PDF file
XCXuehui Chen
Xuehui Chen
WMWeihao Mu
Weihao Mu
XXXin Xu
Xin Xu
LWLIU WEI
LIU WEI
LHLei Huang
Lei Huang
HLHao Li
Hao Li

30 June 2022 in Micromachines
Verified
Journal Article
Open access
PDF file
LWLIU WEI
LIU WEI
SHShan Huang
Shan Huang
SDShuangsong Du
Shuangsong Du
TGTing Gao
Ting Gao
ZZZhengbin Zhang
Zhengbin Zhang
LHLei Huang
Lei Huang
Selective laser melting technology can be used for forming curved panels of 6061 aluminum alloy thermal shield devices for the International Thermonuclear Experimental Reactor (ITER), in order to make the formed parts with better performance. This study proposes different heat treatment processes, including annealed treatment at 300 °C for 2 h, solution treatment at 535 °C and then aging at 175 °C over 2 h, to control the mechanical behavior of the 6061 aluminum alloy samples prepared by selective laser melting (SLM). The mechanical properties such as ductility, tensile strength, and hardness of SLM 6061 aluminum alloy were investigated, and the microstructure of the samples was analyzed. The eutectic silicon skeleton shape disappeared after annealing treatment at 300 °C for 2 h. The tensile strength decreased by 22.86% (from 315 MPa to 243 MPa of the deposited state samples), and the elongation increased from 2.01% to 6.89%. Moreover, the hardness reduced from 120.07 HV0.2 to 89.6 HV0.2. After solution aging, the unique microstructure of SLM disappeared. Furthermore, the precipitation of massive Si particles on the α-Al matrix increased, and a trace amount of the Mg2Si(β) phase was generated. Compared with the deposited samples, the tensile strength decreased by 12.06%, while the hardness of specimens was 118.8 HV0.2. However, the elongation showed a remarkable increase of 297% (from 2.01% to 7.97%). Therefore, solution aging can critically improve the plasticity without losing significant tensile stress in the SLM 6061 aluminum alloy. This study proposes the use of SLM 6061 aluminum alloy for the thermal shields on the ITER and provides a reference for choosing a reasonable heat-treatment method for the optimal performance of the SLM 6061 aluminum alloy.

8 May 2019 in Applied Sciences
Verified
Journal Article
Open access
PDF file
XCXuehui Chen
Xuehui Chen
XLXiang Li
Xiang Li
CWchao wu
chao wu
YMYuping Ma
Yuping Ma
YZYao Zhang
Yao Zhang
LWLIU WEI
LIU WEI
Liquid-assisted laser technology is used to etch defect-free materials for high-precision electronics and machinery. This study investigates water-jet-assisted laser etching of polysilicon material. The depths and widths of the etched grooves were investigated for different water-jet incident angles and velocities. To select optimal parameters for a composite etching processing, the results of many tests must be compared, and at least one set of good processing parameter combinations must be identified. Herein, the influence of different parameters on the processing results is studied using an orthogonal test method. The results demonstrate that the depths and widths of the processing grooves were nearly identical at water-jet angles of 30°and 60°; however, the 60° incidence conferred a slight advantage over 30° incidence. The section taper, section depth, and surface topography were optimized at a water-jet velocity of 24-m/s, 1.1-ms laser pulse width, 40-Hz frequency, and 180-A current. Under these conditions, the section taper and groove depth were 1.2° and 1.88 mm, respectively. The groove surfaces exhibited no splitting, slagging, or other defects, and no recast layers were visible.

14 December 2022 in Applied Surface Science
Verified
Journal Article
Closed access
ZQZhaoling Qiu
Zhaoling Qiu
LJLan Jiang
Lan Jiang
JHJie Hu
Jie Hu
HLHailin Liu
Hailin Liu
LWLIU WEI
LIU WEI
XNXushi Niu
Xushi Niu

4 August 2023 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
XCXuehui Chen
Xuehui Chen
KWKai Wen
Kai Wen
WMWeihao Mu
Weihao Mu
YZYuxi Zhang
Yuxi Zhang
SHShan Huang
Shan Huang
LWLIU WEI
LIU WEI

10 August 2022 in Lubricants
Verified
Journal Article
Open access
PDF file
XCXuehui Chen
Xuehui Chen
YZYuxi Zhang
Yuxi Zhang
CLCongmin Li
Congmin Li
LHLei Huang
Lei Huang
YWYu Wang
Yu Wang
LWLIU WEI
LIU WEI
A large number of joint friction pairs work during the work of scroll compressors, resulting in high energy consumption and short service life of scroll compressors. To improve the tribological performance of friction pairs of the scroll compressors, the C-MoS2-PTFE (Polytetrafluoroethylene) lubrication coating is prepared through spraying technology on the surface of 4032 aluminum alloy, a common material for scroll compressors. The microstructure of the C-MoS2-PTFE coating was analyzed by X-ray diffractometer (XRD) and scanning electron microscope (SEM), and the wear behavior of the coating under different loads was studied by reciprocating friction and wear testing machine and three-dimensional profiler. The surface of the grinding marks was analyzed by SEM and energy density spectrum (EDS). The performance was compared with the anodized film of 4032 aluminum alloy and the Ni-coated coating of 4032 aluminum alloy. The experimental results show that the C-MoS2-PTFE coating has a dense structure, and the hardness is 35 HV0.1. Under dry friction conditions, the C-MoS2-PTFE coating has excellent wear reduction and wear resistance, and the coefficient of friction and wears rate under different loads are less than those of the anodized film of 4032 aluminum alloy and the Ni-plated coating. The wear mechanisms of C-MoS2-PTFE coating are fatigue wear, adhesive wear, abrasive wear, and oxidation wear under different loads.