Simone Kaar

Ms. Simone Kaar


Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 July 2021 in Scripta Materialia
Verified
Journal Article
Open access
SKSimone Kaar
Simone Kaar
KSKatharina Steineder
Katharina Steineder
RSReinhold Schneider
Reinhold Schneider
DKDaniel Krizan
Daniel Krizan
CSChristof Sommitsch
Christof Sommitsch

16 July 2020 in Steel Research International
Verified
Journal Article
Open access
PDF file
SKSimone Kaar
Simone Kaar
DKDaniel Krizan
Daniel Krizan
RSReinhold Schneider
Reinhold Schneider
CSChristof Sommitsch
Christof Sommitsch
Herein, the investigation of the tensile behavior of lean medium Mn Quenching and Partitioning (Q&P) steels containing 0.2 wt% C, 4.5 wt% Mn, and additions of 1.5 wt% Si or 1.3 wt% Al is concentrated upon. By the variation of the quenching temperature (TQ), different volume fractions of primary martensite (α′prim) are adjusted, influencing the subsequent microstructural evolution during Q&P processing. Using scanning electron microscopy (SEM), the final microstructure consisting of tempered martensite (α″), retained austenite (RA), partially bainitic ferrite (αB), and final martensite (α′final) is characterized. Furthermore, interrupted tensile tests at gradually increased strains are conducted to investigate the stability of RA against strain‐induced martensite transformation (SIMT) and overall tensile behavior of lean medium Mn Q&P steels. The investigations manifest the formation of larger amounts of αB and consequently lower RA contents, when Si is substituted by Al. As an aftermath, the tendency to form α′final is significantly lower, compared with the Si‐alloyed composition, reflected in the overall stress–strain behavior. Especially in case of the Si‐alloyed samples containing RA fractions exceeding 15 vol%, an over‐accelerated SIMT is observed, inducing failures occurring prior to necking, whereas for the Al‐alloyed samples, a wider process window is obtained.

19 March 2019 in Metals
Verified
Journal Article
Open access
PDF file
SKSimone Kaar
Simone Kaar
RSReinhold Schneider
Reinhold Schneider
DKDaniel Krizan
Daniel Krizan
CBColine Beal
Coline Beal
Christof SommitschChristof Sommitsch
Christof Sommitsch
The quenching and partitioning (Q&P) process of lean medium Mn steels is a novel approach for producing ultra-high strength and good formable steels. First, the steel is fully austenitized, followed by quenching to a specific quenching temperature (TQ) in order to adjust an appropriate amount of initial martensite (α’initial). Subsequently, the steel is reheated to a partitioning temperature (TP) in order to ensure C-partitioning from α’initial to remaining austenite (γremain) and thus retained austenite (RA) stabilization. After isothermal holding, the steel is quenched to room temperature (RT), in order to achieve a martensitic-austenitic microstructure, where the meta-stable RA undergoes the strain-induced martensitic transformation by the so-called transformation induced plasticity (TRIP) effect. This paper systematically investigates the influence of the Q&P process on the isothermal bainitic transformation (IBT) kinetics in a 0.2C-4.5Mn-1.3Al lean medium Mn steel by means of dilatometry. Therefore, the Q&P annealing approach was precisely compared to the TRIP-aided bainitic ferrite (TBF) process, where the samples were directly quenched to the temperature of the IBT after full austenitization. The results indicated an accelerated IBT for the Q&P samples, caused by the formation of α’initial during quenching below the martensite start (MS) temperature. Furthermore, a significant influence of the annealing parameters, such as TQ and TP, was observed with regard to the transformation behavior. For further characterization, light optical microscopy (LOM) and scanning electron microscopy (SEM) were applied, showing a microstructure consisting of a martensitic-bainitic matrix with finely distributed RA islands. Saturation magnetization method (SMM) was used to determine the amount of RA, which was primarily depending on TQ. Furthermore, the hardness according to Vickers revealed a remarkable impact of the annealing parameters, such as TQ and TP, on the predicted mechanical properties.

19 October 2019 in Metals
Verified
Journal Article
Open access
PDF file
SKSimone Kaar
Simone Kaar
DKDaniel Krizan
Daniel Krizan
RSReinhold Schneider
Reinhold Schneider
CBColine Beal
Coline Beal
Christof SommitschChristof Sommitsch
Christof Sommitsch
The present work focuses on the investigation of both microstructure and resulting mechanical properties of different lean medium Mn Quenching and Partitioning (Q&P) steels with 0.2 wt.% C, 1.5 wt.% Si, and 3–4 wt.% Mn. By means of dilatometry, a significant influence of the Mn-content on their transformation behavior was observed. Light optical and scanning electron microscopy (LOM, SEM) was used to characterize the microstructure consisting of tempered martensite (α’’), retained austenite (RA), partially bainitic ferrite (αB), and final martensite (α’final) formed during final cooling to room temperature (RT). Using the saturation magnetization measurements (SMM), a beneficial impact of the increasing Mn-content on the volume fraction of RA could be found. This remarkably determined the mechanical properties of the investigated steels, since the larger amount of RA with its lower chemical stabilization against the strain-induced martensite transformation (SIMT) highly influenced their overall stress-strain behavior. With increasing Mn-content the ultimate tensile strength (UTS) rose without considerable deterioration in total elongation (TE), leading to an enhanced combination of strength and ductility with UTS × TE exceeding 22,500 MPa%. However, for the steel grades containing an elevated Mn-content, a narrower process window was observed due to the tendency to form α’final.

28 March 2023 in Steel Research International
Verified
Journal Article
Closed access
SKSimone Kaar
Simone Kaar
DKDaniel Krizan
Daniel Krizan
RSReinhold Schneider
Reinhold Schneider
CSChristof Sommitsch
Christof Sommitsch

20 September 2022 in Materialia
Verified
Journal Article
Open access
SKSimone Kaar
Simone Kaar
DKDaniel Krizan
Daniel Krizan
RSReinhold Schneider
Reinhold Schneider
Christof SommitschChristof Sommitsch
Christof Sommitsch