The quenching and partitioning (Q&P) process of lean medium Mn steels is a novel approach for producing ultra-high strength and good formable steels. First, the steel is fully austenitized, followed by quenching to a specific quenching temperature (TQ) in order to adjust an appropriate amount of initial martensite (α’initial). Subsequently, the steel is reheated to a partitioning temperature (TP) in order to ensure C-partitioning from α’initial to remaining austenite (γremain) and thus retained austenite (RA) stabilization. After isothermal holding, the steel is quenched to room temperature (RT), in order to achieve a martensitic-austenitic microstructure, where the meta-stable RA undergoes the strain-induced martensitic transformation by the so-called transformation induced plasticity (TRIP) effect. This paper systematically investigates the influence of the Q&P process on the isothermal bainitic transformation (IBT) kinetics in a 0.2C-4.5Mn-1.3Al lean medium Mn steel by means of dilatometry. Therefore, the Q&P annealing approach was precisely compared to the TRIP-aided bainitic ferrite (TBF) process, where the samples were directly quenched to the temperature of the IBT after full austenitization. The results indicated an accelerated IBT for the Q&P samples, caused by the formation of α’initial during quenching below the martensite start (MS) temperature. Furthermore, a significant influence of the annealing parameters, such as TQ and TP, was observed with regard to the transformation behavior. For further characterization, light optical microscopy (LOM) and scanning electron microscopy (SEM) were applied, showing a microstructure consisting of a martensitic-bainitic matrix with finely distributed RA islands. Saturation magnetization method (SMM) was used to determine the amount of RA, which was primarily depending on TQ. Furthermore, the hardness according to Vickers revealed a remarkable impact of the annealing parameters, such as TQ and TP, on the predicted mechanical properties.
The present work focuses on the investigation of both microstructure and resulting mechanical properties of different lean medium Mn Quenching and Partitioning (Q&P) steels with 0.2 wt.% C, 1.5 wt.% Si, and 3–4 wt.% Mn. By means of dilatometry, a significant influence of the Mn-content on their transformation behavior was observed. Light optical and scanning electron microscopy (LOM, SEM) was used to characterize the microstructure consisting of tempered martensite (α’’), retained austenite (RA), partially bainitic ferrite (αB), and final martensite (α’final) formed during final cooling to room temperature (RT). Using the saturation magnetization measurements (SMM), a beneficial impact of the increasing Mn-content on the volume fraction of RA could be found. This remarkably determined the mechanical properties of the investigated steels, since the larger amount of RA with its lower chemical stabilization against the strain-induced martensite transformation (SIMT) highly influenced their overall stress-strain behavior. With increasing Mn-content the ultimate tensile strength (UTS) rose without considerable deterioration in total elongation (TE), leading to an enhanced combination of strength and ductility with UTS × TE exceeding 22,500 MPa%. However, for the steel grades containing an elevated Mn-content, a narrower process window was observed due to the tendency to form α’final.
Precipitation hardened and tempered martensitic-ferritic steels (TMFSs) are used in many areas of our daily lives as tools, components in power generation industries, or in the oil and gas (O&G) industry for creep and corrosion resistance. In addition to the metallurgical and forging processes, the unique properties of the materials in service are determined by the quality heat treatment (HT). By performing a quenching and partitioning HT during an in situ high energy synchrotron radiation experiment in a dilatometer, the evolution of retained austenite, martensite laths, dislocations, and carbides was characterized in detail. Atomic-scale studies on a specimen with the same HT subjected to a laser scanning confocal microscope show how dislocations facilitate cloud formation around carbides. These clouds have a discrete build-up, and thermodynamic calculations and density functional theory explain their stability.