Mehmet Ayas

Dr. Mehmet Ayas

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 May 2020 in Chemical Engineering Communications
Verified
Journal Article
Closed access
MAMehmet Ayas
Mehmet Ayas
JSJan Skocilas
Jan Skocilas
TJTomáš JIROUT
Tomáš JIROUT
This work reports on an investigation of the relationship between the Reynolds number and the friction factor of the fully developed laminar flow of power-law fluids through non-circular cross-sections (elliptical, concentric annuli, symmetrical L-shape, isosceles triangle, eccentric annuli, and square duct with a central cylindrical core), with the aim of providing a simple method for rapid and simplified engineering calculations. The friction factor—Reynolds number relation has been derived for non-circular ducts on the basis of the modified Reynolds number proposed by Metzner and Reed. It has been shown that the proposed correlation enables a prediction of the friction factor for the fully developed laminar flow of shear thinning fluids in non-circular cross-sections by using a calculation method similar to the method used for laminar flow of a Newtonian fluid. The correlation that is provided has been validated by analytical and numerical methods. It has been found that the proposed method can be used to determine the friction factor with high accuracy. This method yields a friction factor with a deviation of less than 5% in comparison with the conventional method.

29 January 2019 in Chemical Engineering Communications
Verified
Journal Article
Closed access
MAMehmet Ayas
Mehmet Ayas
JSJan Skocilas
Jan Skocilas
TJTomáš JIROUT
Tomáš JIROUT
This article presents a simple and unique method for predicting the friction factor for the fully developed, laminar flow of power-law fluids in ducts with a rectangular cross-section by means of an engineering calculation for rapid equipment design. The relationship between friction factor f and the Reynolds number defined by Metzner–Reed (ReMR) for a rectangular cross-section was investigated and rearranged with very good engineering accuracy using the results of very simple correlations based on the application of the well-known and long-established coefficient for Newtonian fluid flow. The investigated value of the flow index was up to 2, and the aspect ratio ranged from 0 to 1, with calculation error not higher than 3.5%. The proposed method was compared with conventional methods from the literature, and was validated by means of numerical computations, and also with experimental data from the literature. The product of friction factor and ReMR is a linear function of geometrical parameter C and flow behavior index n and also the proposed method predicts the friction factor as accurately as conventional and traditional methods.

8 November 2021 in Asia-Pacific Journal of Chemical Engineering
Verified
Journal Article
Closed access
PDF file
MAMehmet Ayas
Mehmet Ayas
JSJan Skocilas
Jan Skocilas
TJTomáš JIROUT
Tomáš JIROUT

1 August 2020 in Processes
Verified
Journal Article
Open access
PDF file
MAMehmet Ayas
Mehmet Ayas
JSJan Skocilas
Jan Skocilas
TJTomáš JIROUT
Tomáš JIROUT
In this work, the power draw and shear profile of a novel in-line rotor-stator mixer were studied experimentally and the laminar flow regime was simulated. The power draw of the rotor-stator mixer was investigated experimentally using viscoplastic shear-thinning fluid and the results of the obtained power consumptions were verified through simulations. The power draw constant and Otto-Metzner coefficient were determined from the result of experimental data and through simulations. A new method is suggested for the determination of the Otto-Metzner coefficient for the Herschel–Bulkley model and the term efficiency is introduced. It was shown that the proposed method can be applied successfully for the prediction of the Otto-Metzner coefficient for the mixing of viscoplastic shear-thinning fluids. The effect of geometry and rotor speed on power consumption and shear rate profile in the investigated mixer is discussed from the results of the simulations. It was found that numerical methods are a convenient tool and can predict the power draw of the in-line rotor-stator mixer successfully.

10 June 2023 in Journal of Food Engineering
Verified
Journal Article
Closed access
MAMehmet Ayas
Mehmet Ayas
JSJan Skočilas
Jan Skočilas
JŠJan Štípek
Jan Štípek
RŽRudolf Žitný
Rudolf Žitný
TJTomáš Jirout
Tomáš Jirout

7 December 2022 in Polymers
Verified
Journal Article
Open access
PDF file
MAMehmet Ayas
Mehmet Ayas
JSJan Skocilas
Jan Skocilas
JŠJan Štípek
Jan Štípek
CGCarlos Arce Gutiérrez
Carlos Arce Gutiérrez
RZRudolf Zitny
Rudolf Zitny
TJTomáš JIROUT
Tomáš JIROUT
The objective of this study is to provide a straightforward generalized simple and quick method for the prediction of the friction factor for fully developed laminar flow of viscoplastic shear-thinning fluids in non-circular channels of regular cross-sections. The most frequently represented substances processed under these conditions are polymers in the processing and plastics industry. A generalized approximate method was proposed to express the relationship between the friction factor and the Reynolds number for the Herschel–Bulkley rheological model. This method uses the generalized Reynolds number for power-law fluids. Moreover, an additional simplified method for rapid engineering calculations was obtained as well. The suggested method was verified by comparing experimental data for concentric annulus found in the literature and results from simulations for concentric annulus, rectangular, square duct with a central cylindrical core and elliptical cross-sections. The results showed that the suggested methods enable us to estimate the friction factor with high accuracy for the investigated geometries.