Due to climate change, two-thirds of mankind will face water scarcity by 2025, while by 2050, global food production must increase by at least 50% to feed 9 billion people. To overcome water scarcity, 15 million m³/day of untreated wastewater is used globally for crop irrigation, polluting the soil with pathogens, heavy metals and excess salts. Since 10% of the global population consumes food from crops irrigated with wastewater, pathogens transmitted through the food chain cause diseases especially in young children and women. In this paper, we discuss the status of water scarcity and the challenges to food security, the reuse of wastewater in agriculture and the possible risks to human and environmental health. The efficiency of different irrigation systems in limiting the risks of wastewater reuse and the latest regulations of the European Commission on effluent recovery are also presented. Hence, we emphasize that irrigation offers real perspectives for large-scale recovery of wastewater, helping to reduce the deficit and conserve water resources, and increasing food safety, with the express mention that investments must be made in wastewater treatment plants and wastewater must be properly treated before recovery, to limit the risks on human health and the environment.

In order to obtain bioenergy (biogas, biofuel) or pellets, different types of lignocellulosic biomass are subjected to a mechanical pretreatment, first by size reduction, then by separating, and ultimately by fracturing or bio-refining. Biomass processing mainly refers to a grinding process that occurs until reaching certain limits. The size reduction process, such as grinding, is an operation that is executed with different levels of energy consumption, considering biomass mechanical characteristics and the necessary grinding level. This paper, illustrates a comparative analysis of experimental results obtained by grinding multiple types of vegetal biomass (Miscanthus, corn stalks, alfalfa, willow) used in the process of bio-refining and bio-fracturing. Experiments were realized using both a laboratory knife mill Grindomix GM200 (Retsch GmbH, Haan, Germany), and a 22 kW articulated hammer mill, using different grinding system speeds and different hammer mill sieves. Results have shown that biomass mechanical pre-processing grinding leads to supplementary costs in the overall process through bio-refining or bio-fracturing in order to obtain bio-products or bio-energy. So, specific energy consumption for grinding using a hammer mill can reach 50–65 kJ/kg for harvested Miscanthus biomass, and 35–50 kJ/kg for dried energetic willow, using a 10 mm orifice sieve, values which increase processing costs.

This paper presents an analysis of the literature that studies the possibility of sewage sludge being used in the cement industry to reduce carbon dioxide emissions from cement production and thus solve the problem of disposing of sewage sludge so that it is no longer stored, avoiding soil pollution with heavy metals, and reducing pressure on the environment. The ash of sewage sludge is a good pozzolanic material, because when it is finely ground, it can be used as a partial substitute for Portland cement. This reduces waste storage costs. Sewage sludge ash was mixed with cement, and it was analyzed to determine whether the paste obtained could be used as a raw material in the cement industry. The presented results are on the hydration characteristics of the sewage sludge ash, the compressive strength of the cement determined after different days, the workability of the cement, and the porosity of the cement paste and the ash.

Considering that worldwide the amount of sludge from sewage treatment plants has increased, which through storage pollutes the environment, solutions must be found for its management. In this paper, through an analysis of studies from the literature, we present an ecological method of recovery of sewage sludge (SS) in agriculture through vermicomposting with Eisenia etida, Eisenia andrei, Eudrilus eugeniae and Perionyx excavatus earthworms, thus we analyzed the possibility that sewage sludge can be transformed from waste into quality fertilizer that benefits the soil, plants, and people, thus being able to replace chemical fertilizers which, if applied to the soil, can acidify and pollute the soil and agricultural crops. We observed that the total nitrogen content of the phosphorus increased. Through the vermicomposting process, organic substances are rapidly decomposed and nitrogen mineralization is accelerated. We studied the impact of dewatered sewage sludge vermicomposting on pH value, electrical conductivity, porosity, moisture content, nitrogen content, water retention capacity, metal content, and the development of agricultural crops, highlighting the positive impact of vermicompost application on the soil. Adding vermicompost to the soil has been observed to improve plant development.

Our paper presents the hammer mill working process optimization problem destined for milling energetic biomass (MiscanthusGiganteus and Salix Viminalis). For the study, functional and constructive parameters of the hammer mill were taken into consideration in order to reduce the specific energy consumption. The energy consumption dependency on the mill rotor spinning frequency and on the sieve orifices in use, as well as on the material feeding flow, in correlation with the vegetal biomass milling degree was the focus of the analysis. For obtaining this the hammer mill was successively equipped with 4 different types of hammers that grind the energetic biomass, which had a certain humidity content and an initial degree of reduction ratio of the material. In order to start the optimization process of hammer mill working process, 12 parameters were defined. The objective functions which minimize hammer mill energy consumption and maximize the milled material percentage with a certain specific granulation were established. The results obtained can serve as the basis for choosing the optimal working, constructive, and functional parameters of hammer mills in this field, and for a better design of future hammer mills.