Wern Kam

Dr. Wern Kam

orcid

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 October 2013 in Ionics
Verified
Journal Article
Closed access
PDF file
WKWern Kam
Wern Kam
CLChiam-Wen Liew
Chiam-Wen Liew
JLJ. Y. Lim
J. Y. Lim
RTRamesh T.Subramaniam
Ramesh T.Subramaniam

7 February 2017 in Journal of Modern Optics
Verified
Journal Article
Closed access
RZROZALINA ZAKARIA
ROZALINA ZAKARIA
WKWern Kam
Wern Kam
YOY. S. Ong
Y. S. Ong
SYS. F. A. Z. Yusoff
S. F. A. Z. Yusoff
HAHarith Ahmad
Harith Ahmad
Waleed S MohammadWaleed S Mohammad
Waleed S Mohammad
This paper describes simulation and experimental methods for designing a D-shaped surface plasmon resonance (SPR) fibre sensor. The sensor consists of two set-up approaches. Finite element method is used in simulation on the fibre sensor device. Two experimental methods for detecting relative intensity are used by varying the wavelength of the optical signal sources and the thickness of gold layer coated on the D-shaped fibre. In the first method, the sensor device works by detecting the relative intensity of two optical signal sources having different wavelengths. In the second set-up, the relative intensity between two D-shaped fibres coated with different thicknesses of gold is measured when a single signal source is launched at the input. The difference in intensities of the signal outputs is used to estimate the refractive index at the sensing region. A prototype SPR D-shaped fibre sensor has been fabricated and the experimental results show good agreement with simulation.

2 December 2022 in IEEE Sensors Journal
Verified
Journal Article
Open access
Michael MartynMichael Martyn
Michael Martyn
WKWern Kam
Wern Kam
PWPeter Woulfe
Peter Woulfe
SOSinead O'Keeffe
Sinead O'Keeffe
This work considers the feasibility of using a novel optical fiber based sensor, employing a Terbium-doped Gadolinium Oxysulfide (Gd2O2S:Tb) inorganic scintillator, as a real-time in-vivo dosimetry solution for applications in low dose rate (LDR) prostate brachytherapy (BT). This study specifically considers the influence of scintillator geometry (hemi-sphere tip vs cylindrical cavity), PMMA fiber core diameter (0.5 mm vs 1.0 mm), and sensor housing material (stainless steel vs plastic) on the measured scintillation signal. Characterization measurements were performed using a Silicon Photon-Multiplier (SiPM) detector and a commercial water phantom system, integrated with custom 3D printed components to allow for precise positioning of the LDR BT radiation source with respect to the optical fiber sensor. Significant differences in the rate of fall-off in the scintillation signal, with distance from the source, were observed between the different scintillator geometries considered. The hemi-sphere tip geometry was shown to be the most accurate, tracking with the expected fall-off in dose-rate, within measurement uncertainty. Reducing the fiber core diameter from 1.0 mm to 0.5 mm resulted in a 6-fold reduction in the detected scintillation signal. A further 57 % reduction was observed when housing the 0.5 mm fiber within a stainless steel LDR BT needle applicator. Initial results demonstrate the feasibility of employing an optical fiber sensor, for applications in LDR BT, given the excellent agreement of measurements with theoretical expectations. Furthermore a calibration process has been described for converting the detected scintillation signal into absorbed dose / dose-rate, using our water phantom based experimental set-up.

1 April 2014 in Optics and Lasers in Engineering
Verified
Journal Article
Closed access
WKWern Kam
Wern Kam
YOY.S. Ong
Y.S. Ong
WLW.H. Lim
W.H. Lim
RZR. Zakaria
R. Zakaria

1 October 2015 in IEEE Photonics Journal
Verified
Journal Article
Open access
YOY. S. Ong
Y. S. Ong
WKWern Kam
Wern Kam
SHS. W. Harun
S. W. Harun
RZR. Zakaria
R. Zakaria
Waleed S MohammadWaleed S Mohammad
Waleed S Mohammad
This work presents a new low-cost and environmentally friendly optical transducer based on surface scattering in a side-polished fiber mounted on a glass groove. The surface roughness caused by polishing is used to estimate the change in refractive index on top of the fiber. Changing the surrounding index affects the scattering properties and, consequently, the leakage of the guided mode. This effect is experimentally investigated through the change in the attenuation coefficient when the surrounding refractive index is changed by dropping different weight ratios of glucose solutions onto the polished side. The measured change of the attenuation coefficient is consistent with the finite-element calculations. The effect of different polished depths was theoretically investigated to optimize the working conditions.

5 June 2014 in IEEE Sensors Journal
Verified
Journal Article
Closed access
RZRozalina Zakaria
Rozalina Zakaria
OSOng Yong Sheng
Ong Yong Sheng
WKWern Kam
Wern Kam
SSShahaboddin Shamshirband
Shahaboddin Shamshirband
DPDalibor Petkovic
Dalibor Petkovic
NPNenad T. Pavlovic
Nenad T. Pavlovic
An adaptive neurofuzzy (ANFIS) evaluation study has been applied on tapered plastic multimode sensors. This study is basically using tapered plastic multimode fiber polymethyl methacrylate (PMMA) optical as a sensor. It is proposed and demonstrated for continuous monitoring of solutions based on different concentration of sodium chloride and glucose in deionized water. The tapered PMMA fiber was fabricated using an etching method involving deionized water and acetone to achieve a waist diameter and length of 0.45 and 10 mm, respectively. In addition, a tapered PMMA probe, which was coated by silver film, was fabricated and demonstrated using calcium hypochlorite (G70) solution. The working mechanism of such a device is based on the observation increment in the transmission of the sensor that is immersed in solutions at higher concentration. As the concentration varies from 0 to 6 ppm, the output voltage of the sensor increases linearly from 3.61 to 4.28 mV with a sensitivity of 0.1154 mV/ppm and a linearity of more than 99.47%. The silver film coating increases the sensitivity of the proposed sensor due to the effective cladding refractive index, which increases with the coating and thus allows more light to be transmitted from the tapered fiber. To estimate the output voltage response of the sensors with and without silver film, this paper constructed a process, which simulates the sensors voltage output in regard to different concentration of calcium hypochlorite with ANFIS method. This intelligent estimator is implemented using MATLAB/SIMULINK and the performances are investigated. The simulation results presented in this paper show the effectiveness of the developed method.