In this paper, we experimentally demonstrate a highly sensitive on-chip photonic electromagnetic wave sensor operating at 14.1 GHz with a 3 dB bandwidth of 4.84 GHz. The demonstrated electromagnetic sensor has several important advantages over conventional electrical electromagnetic sensors including high sensitivity, compact in size and strong immunity to electromagnetic interference (EMI). The sensor is comprised of a bowtie antenna and an asymmetric Mach-Zehnder interferometer (MZI). One arm of the MZI is an electro-optic (EO) polymer infiltrated one-dimensional (1D) slot photonic crystal waveguide (SPCW) and the other is a strip waveguide with teeth of subwavelength pitch. Bowtie antennas are designed and optimized to effectively collect 14.1 GHz microwave signal and applies it across the SPCW. The phase of the light guided in the SPCW therefore changes, and so does the amplitude of the output end of the MZI. The sensor is only 4.6 mm × 4.8 mm in size and has a low insertion loss of ~ 10 dB. Experimental results show the limit of detection at 14.1 GHz is 4.31 mW/m2, which is corresponding to a minimum detectable electric field of 1.8 V/m
29 April 2019 in IEEE Antennas and Propagation Magazine
We propose and demonstrate a novel design of a multi arm bowtie antenna (MABA) able to provide wideband field enhancement (FE). FE is a looked-for parameter of antennas in integrated electro-optic (EO) communication and sensing applications. In the proposed MABA, the paralleled arms with different lengths and flare angles provide multiple resonance frequencies. By tailoring these resonance frequencies adequately close to each other, a wide range of frequencies with high FE is achieved and the intrinsic limitation of conventional bowtie antennas in this regard is overcome. The proposed MABA is designed at the center frequency of 66.2 GHz and fabricated on a silicon on insulator (SOI) substrate with 1.69 mm × 0.21 mm dimensions. Simulation and measurement results show about 40° beam width and 63.4 dB FE peak with 27 GHz bandwidth which is 3 times larger than the bandwidth of a conventional bowtie antenna (BA), as the most commonly used antenna for this application, on the same substrate. A figure of merit (FoM) is proposed to study performance of antennas for integrated EO applications approximately independent from the effects of substrate, operating frequency, and optical parts. The FoM is calculated and a comparison is presented for different state-of-the-art antennas in literature showing 2.28 times better performance of the proposed MABA.
In this paper, we propose a frequency-independent method for calculation of scattered electromagnetic (EM) fields by the human body in millimeter-wave (MMW) band. The surface of the body is accurately modeled by non-uniform rational B-spline (NURBS) surfaces and is illuminated by a plane wave. The scattered EM fields are formulated by physical optics (PO) approximation. This approximation yields PO surface highly oscillatory integrals that are solved by numerical steepest descent path (NSDP) method, frequency-independently. This paper provides an efficient and accurate method for considering human body in indoor propagation, surveillance and medical imaging, and detection of human body by radiometry.
This paper reports the first high speed roll-to-roll printable transistor using a carbon nanotube (CNT) semiconducting layer. The transistor is made possible through the development of a pulsed light curable CNT ink compatible with typical drop on demand inkjet cartridges. This CNT ink uses a xylene based solvent with methanol, glycerin, and Triton X-100 modifiers to create an evaporable solution with appropriate absorption spectra for a mercury or xenon flash lamp with strong energy transmission in the UVB to mid visible light range, allowing the solution to absorb the energy from the flash lamp and evaporate. Transistor dimensions were defined by the capabilities of a typical roll-to-roll drop on demand cartridge. The final device demonstrated an on/off ratio of 104, representing performance similar to gravure printed devices. This represents the first CNT ink which can be used in high speed production methods without long thermal curing steps in the workflow.
A distortion measurement method is presented for highly-linear wideband optical links. By notching a spur-free region inside signal band before the link and isolating the notch after the link, SFDR of 118.6 dB/Hz2/3 is demonstrated.