Peter Grubb

Mr. Peter Grubb

orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 July 2018 in IEEE Transactions on Components, Packaging and Manufacturing Technology
Verified
Journal Article
Closed access
WLWen Tao Li
Wen Tao Li
YHYong Qiang Hei
Yong Qiang Hei
PGPeter Grubb
Peter Grubb
XSXiao-Wei Shi
Xiao-Wei Shi
RCRay T. Chen
Ray T. Chen
This paper presents a bandwidth-enhanced, low-cost, compact, inkjet-printed multilayer microstrip fractal patch antenna for integration into flexible and conformal devices. The antenna consists of two layers of patches, with the first layer inkjet-printed directly on a 0.125-mm (only 0.005 of the operating wavelength) Kapton polyimide substrate. On top of it, a 0.12-mm-thick SU-8 polymer is covered. To achieve the desired miniaturization and good impedance match, a Minkowski fractal geometry patch is employed as the second layer inkjet-printed on top of the SU-8 polymer. The proposed antenna has compact dimensions of only 22x31 mm² and covers 4.79-5.04-GHz frequency spectrum with S₁₁ < -10 dB. Moreover, a 2-bit 1x 4 phased array antenna (PAA) is constructed, and its scan ability is estimated to demonstrate its potential application in the true-time-delay flexible PAA systems. The prototype is fabricated and tested for impedance and radiation characteristics. The measured and the simulation results show the superiority of the proposed antenna.

26 April 2017 in Scientific Reports
Verified
Journal Article
Open access
PDF file
PGPeter Grubb
Peter Grubb
HSHarish Subbaraman
Harish Subbaraman
SPSaungeun Park
Saungeun Park
DADeji Akinwande
Deji Akinwande
RCRay Chen
Ray Chen
This paper reports a 100% inkjet printed transistor with a short channel of approximately 1 µm with an operating speed up to 18.21 GHz. Printed electronics are a burgeoning area in electronics development, but are often stymied by the large minimum feature size. To combat this, techniques were developed to allow for the printings of much shorter transistor channels. The small gap size is achieved through the use of silver inks with different chemical properties to prevent mixing. The combination of the short channel and semiconducting carbon nanotubes (CNT) allows for an exceptional experimentally measured on/off ratio of 106. This all inkjet printed transistor allows for the fabrication of devices using roll-to-roll methodologies with no additional overhead compared to current state of the art production methods.

18 September 2020 in Micromachines
Verified
Journal Article
Open access
PDF file
Mahmuda Akter MonneMahmuda Akter Monne
Mahmuda Akter Monne
PGPeter Grubb
Peter Grubb
HSHarold Stern
Harold Stern
Harish SubbaramanHarish Subbaraman
Harish Subbaraman
RCRay Chen
Ray Chen
MCMaggie Chen
Maggie Chen
Low-cost and conformal phased array antennas (PAAs) on flexible substrates are of particular interest in many applications. The major deterrents to developing flexible PAA systems are the difficulty in integrating antenna and electronics circuits on the flexible surface, as well as the bendability and oxidation rate of radiating elements and electronics circuits. In this research, graphene ink was developed from graphene flakes and used to inkjet print the radiating element and the active channel of field effect transistors (FETs). Bending and oxidation tests were carried out to validate the application of printed flexible graphene thin films in flexible electronics. An inkjet-printed graphene-based 1 × 2 element phased array antenna was designed and fabricated. Graphene-based field effect transistors were used as switches in the true-time delay line of the phased array antenna. The graphene phased array antenna was 100% inkjet printed on top of a 5 mil flexible Kapton® substrate, at room temperature. Four possible azimuth steering angles were designed for −26.7°, 0°, 13°, and 42.4°. Measured far-field patterns show good agreement with simulation results.

29 April 2019 in IEEE Antennas and Propagation Magazine
Verified
Journal Article
Closed access
FKFarzad Mokhtari Koushyar
Farzad Mokhtari Koushyar
PGPeter Grubb
Peter Grubb
MCMaggie Yihong Chen
Maggie Yihong Chen
RCRay T. Chen
Ray T. Chen

Verified
Journal Article
Open access
PDF file
PGPeter Grubb
Peter Grubb
FKFarzad Mokhtari Koushyar
Farzad Mokhtari Koushyar
TLTravis Lenz
Travis Lenz
AAAref Asghari
Aref Asghari
GGGongwen Gan
Gongwen Gan
RCRay Chen
Ray Chen
This paper reports the first high speed roll-to-roll printable transistor using a carbon nanotube (CNT) semiconducting layer. The transistor is made possible through the development of a pulsed light curable CNT ink compatible with typical drop on demand inkjet cartridges. This CNT ink uses a xylene based solvent with methanol, glycerin, and Triton X-100 modifiers to create an evaporable solution with appropriate absorption spectra for a mercury or xenon flash lamp with strong energy transmission in the UVB to mid visible light range, allowing the solution to absorb the energy from the flash lamp and evaporate. Transistor dimensions were defined by the capabilities of a typical roll-to-roll drop on demand cartridge. The final device demonstrated an on/off ratio of 104, representing performance similar to gravure printed devices. This represents the first CNT ink which can be used in high speed production methods without long thermal curing steps in the workflow.

18 December 2018 in Materials Research Express
Verified
Journal Article
Closed access
PDF file
PGPeter Grubb
Peter Grubb
LWLi Wentao
Li Wentao
RCRay T Chen
Ray T Chen
This paper presents the first frequency scanning array on a flexible substrate constructed using printed electronics methods and systems. Devices were designed using a printed wide band stacked ellipsoid antenna and phase shifter network with 50 ohm matching power splitters which was developed using Ansys Electromagnetics. These devices were produced in both 1x4 and 1x8 antenna patch configurations. The resulting devices were then tested to demonstrate beam steering as a function of frequency at 4.35 GHz, 5.32 GHz, 6.27 GHz, and 7.2 GHz and compared. Additionally, bending tests were performed to demonstrate the usability of the devices in a flexible, internet of things oriented application. The demonstrated devices have a multibeam receiving and transmitting capability while being inexpensive and easy to produce in a flexible package.