Alex Díaz-Molina

Mr. Alex Díaz-Molina

orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2018 in Applied Mathematical Modelling
Verified
Journal Article
Closed access
DGDavid Ruiz Gracia
David Ruiz Gracia
ADAlex Díaz-Molina
Alex Díaz-Molina
OSOle Sigmund
Ole Sigmund
ADAlberto Donoso
Alberto Donoso
JBJosé Carlos Bellido
José Carlos Bellido
Jose-luis Sanchez-RojasJose-luis Sanchez-Rojas
Jose-luis Sanchez-Rojas

3 June 2017 in Actuators
Verified
Journal Article
Open access
PDF file
JTJavier Toledo
Javier Toledo
VRVictor Ruiz-Díez
Victor Ruiz-Díez
ADAlex Díaz-Molina
Alex Díaz-Molina
DGDavid Ruiz Gracia
David Ruiz Gracia
ADAlberto Donoso
Alberto Donoso
Jose-luis Sanchez-RojasJose-luis Sanchez-Rojas
Jose-luis Sanchez-Rojas
In this paper, two different piezoelectric microactuator designs are studied. The corresponding devices were designed for optimal in-plane displacements and different high flexibilities, proven by electrical and optical characterization. Both actuators presented two dominant vibrational modes in the frequency range below 1 MHz: an out-of-plane bending and an in-plane extensional mode. Nevertheless, the latter mode is the only one that allows the use of the device as a modal in-plane actuator. Finite Element Method (FEM) simulations confirmed that the displacement per applied voltage was superior for the low-stiffness actuator, which was also verified through optical measurements in a quasi-static analysis, obtaining a displacement per volt of 0.22 and 0.13 nm/V for the low-stiffness and high-stiffness actuator, respectively. In addition, electrical measurements were performed using an impedance analyzer which, in combination with the optical characterization in resonance, allowed the determination of the electromechanical and stiffness coefficients. The low-stiffness actuator exhibited a stiffness coefficient of 5 × 104 N/m, thus being more suitable as a modal actuator than the high-stiffness actuator with a stiffness of 2.5 × 105 N/m.

27 April 2019 in Micromachines
Verified
Journal Article
Open access
PDF file
ADAlex Díaz-Molina
Alex Díaz-Molina
VRVictor Ruiz-Díez
Victor Ruiz-Díez
JHJorge Hernando-Garcia
Jorge Hernando-Garcia
AAAbdallah Ababneh
Abdallah Ababneh
HSHelmut Seidel
Helmut Seidel
Jose-luis Sanchez-RojasJose-luis Sanchez-Rojas
Jose-luis Sanchez-Rojas
A micro- to milli-sized linear traveling wave (TW) actuator fabricated with microelectromechanical systems (MEMS) technology is demonstrated. The device is a silicon cantilever actuated by piezoelectric aluminum nitride. Specifically designed top electrodes allow the generation of TWs at different frequencies, in air and liquid, by combining two neighboring resonant modes. This approach was supported by analytical calculations, and different TWs were measured on the same plate by laser Doppler vibrometry. Numerical simulations were also carried out and compared with the measurements in air, validating the wave features. A standing wave ratio as low as 1.45 was achieved in air, with a phase velocity of 652 m/s and a peak horizontal velocity on the device surface of 124 μm/s for a driving signal of 1 V at 921.9 kHz. The results show the potential of this kind of actuator for locomotion applications in contact with surfaces or under immersion in liquid.

30 May 2017
Verified
Conference Paper
Closed access
PDF file
DGDavid Ruiz Gracia
David Ruiz Gracia
ADAlex Díaz-Molina
Alex Díaz-Molina
OSO. Sigmund
O. Sigmund
ADA. Donoso
A. Donoso
JBJ. C. Bellido
J. C. Bellido
Jose-luis Sanchez-RojasJose-luis Sanchez-Rojas
Jose-luis Sanchez-Rojas

23 November 2017 in Journal of Physics: Conference Series
Verified
Conference Paper
Open access
PDF file
ADAlex Díaz-Molina
Alex Díaz-Molina
JHJorge Hernando-Garcia
Jorge Hernando-Garcia
Jose-luis Sanchez-RojasJose-luis Sanchez-Rojas
Jose-luis Sanchez-Rojas
This work describes the performance in terms of displacement of two different in-plane piezoelectrically-actuated microactuators: a gripper and an extensional actuator. The materials and the corresponding thicknesses were varied in search of the best configuration for maximum displacement. Three different combinations of materials were considered: AlN/silicon, AlN/polyimide and PVDF/polyimide. A static finite element analysis allowed the calculation of the in-plane displacement. Reduction in the displacement per volt was observed when the thickness of the structure was increased. Despite the fact that polymeric materials are significantly less stiff than silicon, having potential advantages, our simulations reveal that it does not translate into the corresponding improvement in displacement per volt.