Zhongliang Lu

Zhongliang Lu


Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 October 2022 in Metals
Verified
Journal Article
Open access
PDF file
ZLZhefeng Liu
Zhefeng Liu
KMKai Miao
Kai Miao
WLWeibo Lian
Weibo Lian
ZLZhongliang Lu
Zhongliang Lu
DLDichen Li
Dichen Li
The stray grain defect is often found at the platform in the process of directional solidification of single crystal blades because local undercooling easily occurs in this area. A variable wall thickness mold based on stereolithography and gelcasting technology was proposed to solve the local undercooling at the platform. The influence of variable wall thickness mold on the temperature field of the platform during directional solidification was studied via simulation. The numerical simulation results show that variable wall thickness can effectively prevent heat dissipation at the platform, thereby reducing the undercooling and avoiding the formation of stray grains. At the same time, the influence of molds assembly angle on the formation of stray grains was analyzed, and the appropriate molds assembly angle is suggested.

9 March 2022 in Crystals
Verified
Journal Article
Open access
PDF file
ZLZhongliang Lu
Zhongliang Lu
YHYu Han
Yu Han
YGYunpeng Gao
Yunpeng Gao
FCfusheng cao
fusheng cao
HZHaitian Zhang
Haitian Zhang
DLDichen Li
Dichen Li
Laser powder bed fusion (LPBF) technology is of great significance to the rapid manufacturing of high-performance metal parts. To improve the mechanical behavior of an LPBFed AlSi10Mg alloy, the influence of nano-Si3N4 reinforcement on densification behavior, microstructure, and tensile property of AlSi10Mg was studied. The experimental results show that 97% relative density of the 3 vol.% nano-Si3N4/AlSi10Mg composite was achieved via optimization of the LPBF process. With the increase in the nano-Si3N4 content, the tensile strength and the yield strength of the composite steadily increase as per the Orowan strengthening mechanism while the elongation decreases. In addition, nano-Si3N4 reinforcement reduces the width of the coarse cell structure region and the thermal influence region of the AlSi10Mg matrix. After annealing, the tensile strength of the nano-Si3N4/AlSi10Mg composite decreases and the elongation increases significantly.

25 August 2022 in Crystals
Verified
Journal Article
Open access
PDF file
FCfusheng cao
fusheng cao
HZHaitian Zhang
Haitian Zhang
HZHang Zhou
Hang Zhou
YHYu Han
Yu Han
SLSai Li
Sai Li
DLDichen Li
Dichen Li
FeCrAl alloy has been proposed as an alternative material for accident-tolerant fuel (ATF) cladding for nuclear reactors. Thin-wall cladding can be rapidly fabricated by laser powder bed fusion (LPBF). In this paper, a finite element model is established to simulate the transient temperature fields of the cladding under two different laser scanning strategies (linear scanning and ring scanning). In linear scanning simulations, bidirectional scanning, compared with unidirectional scanning, had a smaller temperature gradient along the radial direction. In the ring scanning simulation, the maximum temperature gradually increased and then became stable with the increase of layers. Then, FeCrAl thin-wall cladding with a wall thickness of 0.14 mm was fabricated by LPBF. FeCrAl cladding using the ring scanning strategy had a smaller roughness value (Ra = 4.061 μm). Ring scanning had better accuracy than bidirectional scanning for FeCrAl thin-wall cladding with a wall thickness below 0.4 mm. Therefore, compared with the bidirectional scanning, the ring scanning is more suitable for the high-accuracy manufacturing of FeCrAl thin-wall cladding.

9 December 2021 in Crystals
Verified
Journal Article
Open access
PDF file
LSLi Shidi
Li Shidi
XXXiangyuan Xue
Xiangyuan Xue
JCJiaxing Chen
Jiaxing Chen
TLTengxuan Lu
Tengxuan Lu
ZZZhe Zhao
Zhe Zhao
ZQZhi Qu
Zhi Qu
Currently, the research on mechanical behavior and cutting performance of functionally graded carbides is quite limited, which limits the rapid development of high-performance cemented carbide cutting tools. Based on WC-Co-Zr and WC-Ni-Zr, this study synthesized two kinds of cemented carbide cutters, i.e., the cemented carbide cutters with homogeneous microstructure and functionally graded carbide (FGC) cutters with FCC phase ZrN-enriched surfaces. Furthermore, TiAlN coating has been investigated on these carbide cutters. Mechanical behavior, friction, wear performance, and cutting behavior have been investigated for these coated carbides and their corresponding substrates. It was found that, as compared with coated cutters on WC-Co/Ni-Zr carbide substrates with homogeneous microstructures, the coated cutters on WC-Co/Ni-Zr FGC substrates with FCC phase-enriched surfaces show higher wear resistance and cutting life, and the wear mechanism during cutting is mainly adhesion wear.

1 September 2021 in China Foundry
Verified
Journal Article
Open access
PDF file
ZLZhefeng Liu
Zhefeng Liu
ZLZhongliang Lu
Zhongliang Lu
WLWei-Bo Lian
Wei-Bo Lian
ZLZhongliang Lu
Zhongliang Lu
CYChen Yi
Chen Yi
DLDi-Chen Li
Di-Chen Li
Stray grains, the most serious casting defect, mainly occur in the platform because of the abrupt transition of the cross-section in the directional solidification of superalloy single-crystal blades. A new mould baffle technology based on 3D printing and gelcasting is proposed herein to reduce the formation of stray grains in the platform. The influence of the proposed mould baffle technology on the temperature field in the platform during solidification was investigated by simulation and experiment. The numerical simulation results indicate that the proposed mould baffle technology can effectively hinder the radiation and heat dissipation at the platform extremities, and therefore, reduce undercooling in the platform and the formation of stray grains during directional solidification. Casting trials of a hollow turbine blade were conducted using CMSX-4 superalloy. The trial results demonstrate the potential of the proposed approach for manufacturing single-crystal superalloy blades.

24 August 2021 in Advanced Engineering Materials
Verified
Journal Article
Closed access
PDF file
KMKai Miao
Kai Miao
ZWZhongrui Wang
Zhongrui Wang
RHRan He
Ran He
LJLei Jin
Lei Jin
ZSZhaowei Song
Zhaowei Song
DLDichen Li
Dichen Li