This paper presents the feasibility of a fully inkjet-printed, microwave flexible gas sensor based on a resonant electromagnetic transducer in microstrip technology and the impact of the printing process that affects the characteristics of the gas sensor. The sensor is fabricated using silver ink and multi-wall carbon nanotubes (MWCNTs) embedded in poly (3,4-ethylenedioxythiophene) polystyrene (PEDOT: PSS-MWCNTs) as sensitive material for Volatile Organic Compounds (VOCs) detection. Particular attention is paid to the characterization of the printed materials and the paper substrate. The manufacturing process results in a change in relative permittivity of the paper substrate by nearly 20%. Electrical characterization, made in the presence of gas, validates our theoretical approach and the radiofrequency (RF) gas sensor proof of concept.
Carbon nanotube [CNT] interconnection bump joining methodology has been successfully demonstrated using flip chip test structures with bump pitches smaller than 150 μm. In this study, plasma-enhanced chemical vapor deposition approach is used to grow the CNT bumps onto the Au metallization lines. The CNT bumps on the die substrate are then 'inserted' into the CNT bumps on the carrier substrate to form the electrical connections (interconnection bumps) between each other. The mechanical strength and the concept of reworkable capabilities of the CNT interconnection bumps are investigated. Preliminary electrical characteristics show a linear relationship between current and voltage, suggesting that ohmic contacts are attained.
This paper presents an inkjet-printed differential passive microwave planar resonator-based sensor for toxic vapor detection at room temperature. Two devices are presented, with 5 (D1) and 50 (D2) layers of composite sensitive film (PEDOT:PSS-MWCNTs). Each one consists of two band-pass resonators with the fundamental modes around 2.5 and 2.7 GHz. Theoretical and experimental results are presented, both devices show sensitivity to ethanol vapor ranging from 500 to 1300 ppm according to the magnitude and resonant frequency shifts of their scattering parameters (S-parameters). Limitations due to a continuous drift on both the reference and the sensitive channels are discussed. Though further improvements are needed, such sensor is a good candidate for integration into real-time multi-sensing platforms adaptable for the Internet of Things.
19 June 2006 in IEEE Transactions on Microwave Theory and Techniques
We propose a new low-temperature co-fired ceramic (LTCC) U-shaped resonator. The advantages of LTCC technology are employed to design this three-dimensional (3-D) lambdag/2 resonator. The latter is modeled and optimized by 3-D electromagnetic simulations and is validated by experimental results. In order to validate the coupling between these resonators, a two-pole filter, functioning around 39 GHz, has then been designed and realized with success. Finally, two very compact three-pole bandpass filters have been conceived for a Q-band duplexer design. On the one hand, a filter has been designed around 38 GHz and presents a transmission zero in the upper band. On the other hand, an other filter functioning at 40.7 GHz is presented with a transmission zero in the lower band. Experimental results are in good agreement with theoretical ones
Electromagnetic bandgap (EBG) concept is used to create cavity by dimensioning a variant cell (or defect) inside a 2D EBG material. Compact high unloaded Q cavity (Qu ~ 2500) and narrow two and three pole filters are designed in Ka band. They are manufactured by layer-by-layer stereolithography and made out of high permittivity yttria-stabilized Zirconia. Measurements of the three pole filter working at 33.45GHz exhibits an 1.05% bandwidth and an insertion loss of 1.7dB. These specifications are close to the theoretical values of 33GHz (1.5% shift in central working frequency) and 0.95% bandwidth
18 April 2018 in IEEE Transactions on Nanotechnology
This paper presents the feasibility of a low-cost fully inkjet printed capacitive microwave flexible gas sensor based on a resonant electromagnetic transducer in micro-strip technology with poly (3,4-ethylenedioxythiophene) polystyrene sulfonate and multi wall carbon nanotubes (PEDOT:PSS-MWCNTs) as sensitive material for Volatile Organic Compounds (VOCs) detection. The design and simulation results of the device on paper substrate for differential measurements are first described. This theoretical study based on both analytical and Finite Element Model approaches, validates the operating principle. The fabrication process and experimental devices are then presented, as well as electrical characterization results, both in air and under selected vapor analytes. These experimental results show the good sensor repeatability and sensitivity according to the transmission S parameter resonant frequency shift equal to -2.153 kHz/ppm and -1.855 kHz/ppm for ethanol and toluene vapor concentrations from 500 to 1300 ppm, respectively. This leads to conclude on promising future of such passive sensors and further integration into real-time multi-sensing platform adaptable for the Internet of Things (IoT).