Surface geometry has had an influence on the surface property, in addition to the intrinsic surface energy, of materials. Many physical surface modification methods had been proposed to control the solid surface geometry for modification of surface properties. Recently, short-pulse lasers were utilized to perform nano-texturing onto metallic and polymer substrates for the improvement of surface properties. Most of the papers reported that the hydrophilic metallic surface was modified to have a higher contact angle than 120–150°. Little studies explained the relationship between surface geometry and surface properties. In the present study, the laser micro-/nano-texturing was developed to describe this surface-geometric effect on the static contact angles for pure water. Micropatterns with multi spatial frequencies are designed and synthesized into a microtexture. This tailored microtexture was utilized to prepare for computer aided machining (CAM) data to control the femtosecond laser beams. The nano-length ripples by laser induced periodic surface structuring (LIPSS) supposed onto this microtexture to form the micro-/nano-texture on the AISI304 substrate surface. Computational geometry was employed to describe this geometric profile. The fractal dimension became nearly constant by 2.26 and insensitive to increase of static contact angle (θ) for θ > 150°. Under this defined self-similarity, the micro-/nano-textured surface state was controlled to be super-hydrophobic by increasing the ratio of the highest spatial frequency in microtextures to the lowest one. This controllability of surface property on the stainless steels was supported by tailoring the wavelength and pitch of microtextures. Exposure testing was also used to evaluate the engineering durability of this micro-/nano-textured surface. Little change of the measured fractal dimension during the testing proved that this physically modified AISI304 surface had sufficient stability for its long-term usage in air.
Miniature products and components must be surface treated to improve their wear resistance and corrosion toughness. Among various processes, low-temperature plasma nitriding was employed to harden the outer and inner surfaces of micro-nozzles and to strengthen the micro-springs. A table-top nitriding system was developed even for simultaneous treatment of nozzles and springs. A single AISI316 micro-nozzle was nitrided at 673 K for 7.2 ks to have a surface hardness of 2000 HV0.02 and nitrogen solute content up to 10 mass%. In particular, the inner and outer surfaces of a micro-nozzle outlet were uniformly nitrided. In addition, the surface contact angle increased from 40° for bare stainless steels to 104° only by low-temperature plasma nitriding. A stack of micro-nozzles was simultaneously nitrided for mass production. Micro-springs were also nitrided to improve their stiffness for medical application.
Packaging using thermoplastic molding for hollowed GaN chips were requested for a leak-proof micro-joining between plastic molds and copper-based substrates. The design and engineering of micro-textures is a key technology for putting leak-proof packaging into practice. In the present paper, a micro-meshing punch array was prepared using plasma-nitriding-assisted printing. Two-dimensional original patterns were screen-printed onto an AISI316 die substrate and plasma nitrided at 673 K for 14.4 ks (or 4 h). The unprinted surfaces were selectively nitrogen super-saturated to have more nitrogen content than 5 mass% and a higher hardness than 1200 HV. The printed surfaces were selectively sand blasted to fabricate the micro-meshing punch array for micro-embossing. A computer numerically controlled stamping system was utilized to describe the micro-embossing behavior onto copper substrates and to investigate how the micro-textures on the array was transcribed onto the copper. Reduction of takt time as well as flexibility in the micro-grooving were discussed with reference to the picosecond laser machining and mechanical milling processes.
A diamond-like carbon (DLC) film, coated on a AISI420-J2 stainless steel substrate and vertically aligned graphite (VAG), was structured by high-density plasma oxidation to work as a DLC-punch for micro-stamping and DLC-nozzle array for micro-dispensing, in addition to acting as a copper-plated thermal spreader, respectively. Thick DLC films were micro-patterned by maskless lithography and directly plasma-etched to remove the unmasked regions. Thick VAG (Ca plates were micro-patterned by screen-printing and selectively etched to activate the surface. Raman spectroscopy as well as electric resistivity measurement proved that there was no degradation of VAG by this surface activation. Wet plating was utilized to prove that copper wettability was improved by this surface treatment.
1 September 2019 in Journal of Micro and Nano-Manufacturing
The plasma printing was developed as a means to fabricate the micronozzle chip with the inner diameter less than 50 μm. The initial two-dimensional micropattern was printed onto the stainless steel substrate surface by the maskless lithography. These printed micropatterns were utilized as a mask to make selective nitriding into the unprinted surface. After removal of printed pattern, the un-nitrided surfaces were chemically etched to leave the nitrided microtexture as a micronozzle chip. High nitrogen supersaturation as well as selective nitrogen diffusion had influence on the spatial resolution in this plasma printing in addition to the digitizing error in the maskless lithography.