Biofuels have become an integral part of everyday life in modern society. Bioethanol and fatty acid methyl esters are a common part of both the production of gasoline and diesel fuels. Also, pressure on replacing fossil fuels with bio-components is constantly growing. Waste vegetable fats can replace biodiesel. Hydrotreated vegetable oil (HVO) seems to be a better alternative. This fuel has a higher oxidation stability for storage purposes, a lower temperature of loss of filterability for the winter time, a lower boiling point for cold starts, and more. Viscosity, density, cold filter plugging point of fuel blend, and flash point have been measured to confirm that a fuel from HVO is so close to a fuel standard that it is possible to use it in engines without modification. The objective of this article is to show the properties of different fuels with and without HVO admixtures and to prove the suitability of using HVO compared to FAME. HVO can also be prepared from waste materials, and no major modifications of existing refinery facilities are required. No technology in either investment or engine adaptation of fuel oils is needed in fuel processing.

Biobutanol is a renewable, less polluting, and potentially viable alternative fuel to conventional gasoline. Biobutanol can be produced from same sources as bioethanol, and it has many advantages over the widespread bioethanol. This paper systematically analyzes biobutanol fuel as an alternative to bioethanol in alcohol–gasoline mixtures and the physicochemical properties. Based on the conducted analyses, it was found that biobutanol mixtures have a more suitable behavior of vapor pressure without the occurrence of azeotrope, do not form a separate phase in lower temperature, it has higher energy density, but slightly reduce the octane number and a have higher viscosity. However, in general, biobutanol has many advantageous properties that could allow its use in gasoline engines instead of the commonly used bioethanol.

There is a global need to increase the production of alternative sources of energy due to many issues related to conventional sources, such as environmental degradation or energy security. In this paper, decentralized liquefied natural gas production is analyzed. Liquefied natural gas, according to the analysis, can be considered a viable alternative even for decentralized applications Design and economic analysis of a small-scale biogas LNG plan together with the necessary technology and economic evaluation are presented in the paper. The results show that a project of the proposed size (EUR 3 million) offers a relatively good profitability level. Specifically, the net present value of the project is mostly positive (around EUR 0.1 million up to EUR 0.8 million). Therefore, based on the research, small LNG plants operating across the continent can be recommended for the processing of local sources of biogas.

In this study, 15 selected bottled mineral waters from chosen European countries were tested for their mineral nutrient contents. In particular, six important nutrients (Ca²⁺, Mg²⁺, Na⁺, K⁺, ${\mathrm{HCO}}_3^{-}$, Cl⁻) were measured using atomic absorption spectroscopy. The content of mineral nutrients in all sampled mineral waters were compared to their expected content based on the label. Consequently, their taste was evaluated by 60 trained panelists who participated in the sensory analysis. The results from both the atomic absorption spectroscopy and sensory analysis were analyzed using the regression framework. On the basis of the results from the regression analysis, we determined to what extent the individual mineral nutrients determined the taste of the mineral water. According to the regression results, four out of six analyzed nutrients had a measurable impact on taste. These findings can help producers to provide ideal, health-improving nutrients for mineral water buyers.

This paper focuses on the evaluation of the fuel properties of Fischer–Tropsch diesel blends with conventional diesel. Incorporating this advanced fuel into conventional diesel production will enable the use of waste materials and non-food materials as resources, while contributing to a reduction in dependence on crude oil. To evaluate the suitability of using Fischer–Tropsch diesel, cetane number, cetane index, CFPP, density, flash point, heat of combustion, lubricity, viscosity, distillation curve, and fuel composition ratios using multidimensional GC × GC-TOFMS for different blends were measured. It was found that the fuel properties of the blended fuel are comparable to conventional diesel and even outperform conventional fuel in some parameters. All measurements were performed according to current standards, thus ensuring the repeatability of measurements for other research groups or the private sector.

This article focuses on the issue of motor oils used in the engines of non-road mobile machinery (NRMM), more specifically tractors. The primary goal of the paper is to determine the appropriate replacement interval for these oils. The physical properties of the examined samples were first determined by conventional instruments. Furthermore, the concentrations of abrasive metals, contaminants, and additive elements were measured using an optical emission spectrometer. Lastly, the content of water, fuel, and glycol and the products of oxidation, nitration, and sulfation were determined by using infrared spectrometry. The measured values were compared to the limit values. Based on the processing and evaluation of these analyses, the overall condition of the oils was assessed and subsequently the optimal exchange interval of the examined oils was determined. In addition, a risk analysis of the outage was performed. Due to the high yields of crops, farmers can lose a significant amount of product when a tractor is not functioning during the harvest period. This loss is calculated in the paper.