The nominal power of single wind energy conversion systems (WECS) has been steadily increasing, now reaching power ratings close to 10 MW. In the power conversion stage, medium-voltage power converters are replacing the conventional low-voltage back-to-back topology. Modular multilevel converters have appeared as a promising solution for multi-MW WECSs, due to their modularity and the capability to reach high nominal voltages. This paper discusses the application of the modular multilevel matrix converter to drive multi-MW WECSs. The modeling and control systems required for this application are extensively analyzed and discussed in this paper. The proposed control strategies enable decoupled operation of the converter, provide maximum power point tracking capability at the generator side, grid code compliance at the grid side (including low-voltage ride-through control) and good steady state and dynamic performance for balancing the capacitor voltages in all the clusters. Finally, the effectiveness of the proposed control strategy is validated using simulation and through experimental results obtained with a 27-power-cell prototype.

Modular multilevel converters (M ² C) are considered an attractive solution for high power drive applications. However, energy balancing within the converter is complex to achieve, particularly when the machine is operating at low rotational speeds. In this paper, a new control system, based on cascaded control loops and a vector-power-voltage (vPV) model of the M ² C, is proposed. The control system is implemented in a dq-synchronous frame rotating at ω _e rad/s with the external loop regulating the capacitor voltages using proportional-integral (PI) controllers. The internal loop controls the converter currents using PI and resonant controllers. In addition, the control systems required to operate the machine at other points, i.e., at medium and high rotational speeds, are also discussed in this paper. Experimental results obtained with an M ² C-based drive laboratory prototype with 18 power cells are presented in this paper.

Increase in global energy demand and constraints from fossil fuels have encouraged a growing share of renewable energy resources in the utility grid. Accordingly, an increased penetration of direct current (DC) power sources and loads (e.g., solar photovoltaics and electric vehicles) as well as the necessity for active power flow control has been witnessed in the power distribution networks. Passive transformers are susceptible to DC offset and possess no controllability when employed in smart grids. Solid state transformers (SSTs) are identified as a potential solution to modernize and harmonize alternating current (AC) and DC electrical networks and as suitable solutions in applications such as traction, electric ships, and aerospace industry. This paper provides a complete overview on SST: concepts, topologies, classification, power converters, material selection, and key aspects for design criteria and control schemes proposed in the literature. It also proposes a simple terminology to identify and homogenize the large number of definitions and structures currently reported in the literature.

In three-phase unbalanced systems, where the circulation of zero sequence current is necessary, four-leg converters provide a neutral connection for single-phase or other unbalanced loads typically utilized in three-phase distribution systems. In addition, control of the magnitude and phase of the zero-sequence voltage and/or current are also achieved using four-leg power converters. However, even when four-leg converters have become very important in several fields as for instance, four-leg microgrids and aerospace applications, a comprehensive review of the converter topologies, control methods, modulation methods and output filters have not been hitherto published. In this paper, a comprehensive overview of the state-of-the-art of four-leg converters is presented, based on the selection of over 400 papers published in journals and conferences, identifying mature and incipient topologies, modulation strategies, control schemes and applications. Each topic presented in this work is thoroughly discussed and reviewed, analyzing characteristics, implementation issues, and reported advantages and disadvantages to provide a comprehensive overview of the current research and future challenges in four-leg converters. The most important applications of four-leg converters are also discussed in this work, including stand-alone power supply, uninterruptible power supplies, grid-connected 4-leg inverters, ground power units for aerospace applications, active filtering for power quality enhancement, cooperative control of 4-leg converters for micro-grid applications, among others. Finally, future work and conclusions are highlighted in this paper.

The modular multilevel matrix converter is a relatively new power converter topology suitable for high-power alternating current (AC)-to-AC applications. Several publications in the literature have highlighted the converter capabilities, such as full modularity, fault-redundancy, control flexibility and input/output power quality. However, the topology and control of this converter are relatively complex to realise, considering that the converter has a large number of power-cells and floating capacitors. To the best of the authors’ knowledge, there are no review papers where the applications of the modular multilevel matrix converter are discussed. Hence, this paper aims to provide a comprehensive review of the state-of-the-art of the modular multilevel matrix converter, focusing on implementation issues and applications. Guidelines to dimensioning the key components of this converter are described and compared to other modular multilevel topologies, highlighting the versatility and controllability of the converter in high-power applications. Additionally, the most popular applications for the modular multilevel matrix converter, such as wind turbines, grid connection and motor drives, are discussed based on analyses of simulation and experimental results. Finally, future trends and new opportunities for the use of the modular multilevel matrix converter in high-power AC-to-AC applications are identified.

The rated power of wind turbines has consistently enlarged as large installations can reduce energy production costs. Multi-megawatt wind turbines are frequently used in offshore and onshore facilities, and today is possible to find wind turbines rated over 15 MW. New developments in generators and power converters for multi-MW wind turbines are needed, as the trend toward upscaling the dimensions of wind turbines is expected to continue. Therefore, this paper provides a detailed review of commercially available and recently proposed multi-MW wind turbine generators and power converters. Furthermore, comparative analyses indicate the advantages and disadvantages of commercially available and promising technologies for generators and power converters at the multi-MW target.