The in vivo electrochemical behavior of titanium nitride (TiN) nerve stimulation electrodes was compared to their in vitro behavior for a period of 90 days. Ten electrodes were implanted in two Göttingen minipigs. Four of these were used for electrical stimulation and electrochemical measurements. Five electrodes were kept in Ringer’s solution at 37.5 °C, of which four were used for electrical stimulation and electrochemical measurements. The voltage transients measured in vivo were 13 times greater than in vitro at implantation and they continued to increase with time. The electrochemical properties in vivo and the tissue resistance (Rtissue) followed a similar trend with time. There was no consistent significant difference between the electrochemical properties of the in vivo and in vitro electrodes after the implanted period. The differences between the in vivo and in vitro electrodes during the implanted period show that the evaluation of electrochemical performance of implantable stimulation electrodes cannot be substituted with in vitro measurements. After the implanted period, however, the performance of the in vivo and in vitro electrodes in saline was similar. In addition, the changes observed over time during the post-implantation period regarding the electrochemical properties of the in vivo electrodes and Rtissue were similar, which indicates that these changes are due to the foreign body response to implantation.
Objective. Over the recent years, several small area electrodes have been introduced as tools for preferential stimulation of small cutaneous nerve fibers. However, the performance of the electrodes is highly debated and have not previously been systematically compared. The electrodes have been developed empirically and little is known about the electrical potential they produce in the skin, and how this influences the nerve fiber activation. The objective of the present study was to develop and validate a computational model to compare the preferential stimulation of small fibers for electrodes of different designs. Approach. A finite element model of the skin was developed and coupled with an A β -fiber and an A δ -fiber multi-compartmental nerve fiber model, to describe the current spread and consequent nerve fiber activation produced by five different surface electrodes; intra-epidermal, planar concentric, pin, planar array, and patch. The model was validated through experimental assessments of the strength-duration relationship, impedance, and reaction times. Main results. The computational model predicted the intra-epidermal electrode to be the most preferential for small fiber activation. The intra-epidermal electrode was, however, also found to be the most sensitive to positioning relative to nerve fiber location, which may limit the practical use of the electrode. Significance. The present study highlights the influence of different electrode design features on the current spread and resulting activation of cutaneous nerve fibers. Additionally, the computational model may be used for the optimization of electrode design towards even better preferential stimulation of small fibers.
15 November 2018 in Frontiers in Bioengineering and Biotechnology
Robust devices for chronic neural stimulation demand electrode materials which exhibit high charge injection (Qinj) capacity and long-term stability. Boron-doped diamond (BDD) electrodes have shown promise for neural stimulation applications, but their practical applications remain limited due to the poor charge transfer capability of diamond. In this work, we present an attractive approach to produce BDD electrodes with exceptionally high surface area using porous titanium nitride (TiN) as interlayer template. The TiN deposition parameters were systematically varied to fabricate a range of porous electrodes, which were subsequently coated by a BDD thin-film. The electrodes were investigated by surface analysis methods and electrochemical techniques before and after BDD deposition. Cyclic voltammetry (CV) measurements showed a wide potential window in saline solution (between −1.3 and 1.2 V vs. Ag/AgCl). Electrodes with the highest thickness and porosity exhibited the lowest impedance magnitude and a charge storage capacity (CSC) of 253 mC/cm2, which largely exceeds the values previously reported for porous BDD electrodes. Electrodes with relatively thinner and less porous coatings displayed the highest pulsing capacitances (Cpulse), which would be more favorable for stimulation applications. Although BDD/TiN electrodes displayed a higher impedance magnitude and a lower Cpulse as compared to the bare TiN electrodes, the wider potential window likely allows for higher Qinj without reaching unsafe potentials. The remarkable reduction in the impedance and improvement in the charge transfer capacity, together with the known properties of BDD films, makes this type of coating as an ideal candidate for development of reliable devices for chronic neural interfacing.
Objective. The goal of this study was to assess the electrochemical properties of boron-doped diamond (BDD) electrodes in relation to conventional titanium nitride (TiN) electrodes through in vitro and in vivo measurements. Approach . Electrochemical impedance spectroscopy, cyclic voltammetry and voltage transient (VT) measurements were performed in vitro after immersion in a 5% albumin solution and in vivo after subcutaneous implantation in rats for 6 weeks. Main results . In contrast to the TiN electrodes, the capacitance of the BDD electrodes was not significantly reduced in albumin solution. Furthermore, BDD electrodes displayed a decrease in the VTs and an increase in the pulsing capacitances immediately upon implantation, which remained stable throughout the whole implantation period, whereas the opposite was the case for the TiN electrodes. Significance. These results reveal that BDD electrodes possess a superior biofouling resistance, which provides significantly stable electrochemical properties both in protein solution as well as in vivo compared to TiN electrodes.
The aim of this study was to investigate how the electrochemical properties of porous titanium nitride stimulation electrode are affected by fibrous encapsulation in vivo. Electrochemical impedance spectroscopy (EIS), cyclic voltammetry and voltage transient (VT) measurements were performed in vivo and in phosphate buffered saline, where the encapsulation process is absent. EIS was used as a non-invasive measurement to follow the inflammation, healing and encapsulation process. EIS showed that the healing and encapsulation process lasted 3-4 weeks. The VTs increased during the first 3-4 weeks, after which they stabilized. The charge storage capacity (CSC) decreased most during the first 3-4 weeks. The increasing VTs and decreasing CSC during the first 3-4 weeks after implantation of the in vivo electrodes seem related to healing and fibrous encapsulation. It is suggested that the charge injection pathway during the encapsulation process changes, which implies that charge injection limits are underestimated with conventional methods.