Ala Hijazi

Prof. Ala Hijazi

German Jordanian University

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 November 2020 in Applied Sciences
Verified
Journal Article
Open access
PDF file
AHAla Hijazi
Ala Hijazi
Sameer Al-DahidiSameer Al-Dahidi
Sameer Al-Dahidi
SASafwan Altarazi
Safwan Altarazi
An artificial neural network (ANN) extracts knowledge from a training dataset and uses this acquired knowledge to forecast outputs for any new set of inputs. When the input/output relations are complex and highly non-linear, the ANN needs a relatively large training dataset (hundreds of data points) to capture these relations adequately. This paper introduces a novel assisted-ANN modeling approach that enables the development of ANNs using small datasets, while maintaining high prediction accuracy. This approach uses parameters that are obtained using the known input/output relations (partial or full relations). These so called assistance parameters are included as ANN inputs in addition to the traditional direct independent inputs. The proposed assisted approach is applied for predicting the residual strength of panels with multiple site damage (MSD) cracks. Different assistance levels (four levels) and different training dataset sizes (from 75 down to 22 data points) are investigated, and the results are compared to the traditional approach. The results show that the assisted approach helps in achieving high predictions’ accuracy (<3% average error). The relative accuracy improvement is higher (up to 46%) for ANN learning algorithms that give lower prediction accuracy. Also, the relative accuracy improvement becomes more significant (up to 38%) for smaller dataset sizes.

17 October 2017 in Measurement Science and Technology
Verified
Journal Article
Closed access
PDF file
AHAla Hijazi
Ala Hijazi
AFAlexander Friedl
Alexander Friedl
CCChristian Cierpka
Christian Cierpka
CKChristian Kaehler
Christian Kaehler
VMVis Madhavan
Vis Madhavan
This paper demonstrates the possibility of capturing full-resolution, high-speed image sequences using a regular 3CCD color camera in conjunction with high-power light emitting diodes of three different colors. This is achieved using a novel approach, referred to as spectral-shuttering, where a high-speed image sequence is captured using short duration light pulses of different colors that are sent consecutively in very close succession. The work presented in this paper demonstrates the feasibility of configuring a high-speed camera system using low cost and readily available off-the-shelf components. This camera can be used for recording six-frame sequences at frame rates up to 20 kHz or three-frame sequences at even higher frame rates. Both color crosstalk and spatial matching between the different channels of the camera are found to be within acceptable limits. A small amount of magnification difference between the different channels is found and a simple calibration procedure for correcting the images is introduced. The images captured using the approach described here are of good quality to be used for obtaining full-field quantitative information using techniques such as digital image correlation and particle image velocimetry. A sequence of six high-speed images of a bubble splash recorded at 400 Hz is presented as a demonstration.

18 November 2020 in Materials
Verified
Journal Article
Open access
PDF file
AHAla Hijazi
Ala Hijazi
Sameer Al-DahidiSameer Al-Dahidi
Sameer Al-Dahidi
SASafwan Altarazi
Safwan Altarazi
Multiple site damage (MSD) cracks are small fatigue cracks that may accumulate at the sides of highly loaded holes in aging aircraft structures. The presence of MSD cracks can drastically reduce the residual strength of fuselage panels. In this paper, artificial neural networks (ANN) modeling is used for predicting the residual strength of aluminum panels with MSD cracks. Experimental data that include 147 unique configurations of aluminum panels with MSD cracks are used. The experimental dataset includes three different aluminum alloys (2024-T3, 2524-T3, and 7075-T6), four different test panel configurations (unstiffened, stiffened, stiffened with a broken middle stiffener, and bolted lap-joints), many different panel widths and thicknesses, and the sizes of the lead and MSD cracks. The results presented in this paper demonstrate that a single ANN model can predict the residual strength for all materials and configurations with high accuracy. Specifically, the overall mean absolute error for the ANN model predictions is 3.82%. Furthermore, the ANN model residual strength predictions are compared to those obtained using the most accurate semi-analytical and computational approaches from the literature. The ANN model predictions are found to be at the same accuracy level of these approaches, and they even outperform the other approaches for many configurations.


26 April 2026 in Continuum Mechanics and Thermodynamics
Verified
Journal Article
Closed access
PDF file
AHAla Hijazi
Ala Hijazi
SASameer Al-Dahidi
Sameer Al-Dahidi
ALAlexander Lion
Alexander Lion