A dual-function slot antenna at microwave and millimetre-wave (mm-wave) band is proposed. The design consists of a slot printed on the edge of the structure ground plane. A short-circuited varactor diode is used to achieve frequency tunability from 2.05 to 2.7 GHz (4G, WLAN) with a maximum realized gain of 4.5 dBi. For mm-wave band, the slot works as a connected slot antenna array (CSAA) by using 8 periodic feeders with a wide bandwidth of 23-29 GHz (5G) and a maximum realized gain of 12.5 dBi. To enhance functionality, two slots are arranged orthogonally for multiple-input multiple-output (MIMO) application. The whole structure is implemented using Rogers 5880 substrate with a board size of 70×60×0.381 mm3. The envelope correlation coefficient (ECC) and isolation are calculated, showing satisfactory MIMO characteristics. The minimum ECC value is 0.01, while the isolation is more than 20 dB among different feeding ports. Due to the integration of 4G and 5G operation into a single narrow slot, the proposed antenna system is compact, simple and planar in structure, and thus, attractive for future mobile handheld devices.
21 November 2008 in IEEE Transactions on Antennas and Propagation
The paper reports on investigations into phase characteristic of a unit cell of a single-layer microstrip reflectarray, which includes patch or ring elements of variable size. The aim is to have a smaller gradient (slower slope) of the reflected wave phase as a function of the elements' size to achieve a wider operational bandwidth and smaller susceptibility to manufacturing errors. The results obtained for single resonance elements demonstrate that a slower slope can be achieved using thicker substrates at the expense of an inadequate phase range of less than 300deg. This inadequate phase range leads to the reflectarray elements phase errors, which reduce its directivity. To overcome this problem the use of multiresonance multiring elements is postulated. It is shown that square and circular shaped multiple rings printed on a thick substrate can offer a slower phase slope and the phase range exceeding 360deg. The achieved slopes and ranges of double rings are comparable with those of double stacked patches printed on the equivalent low permittivity dielectric substrate. Choosing suitable dimensions of double-ring elements, the phase characteristic can be made approximately a linear function of their size.
2 April 2020 in IEEE Transactions on Antennas and Propagation
An accurate equivalent-circuit (EC) design approach for wideband nonmagnetic absorbers operating at the low microwave frequency (1 – 10 GHz) is presented. Following the impedance matching approach, this study introduces an EC model based on simulated data and synthetic asymptotes for single- and double-layer FSS-based non-magnetic absorbers. Two simple and commonly used resistive frequency selective surfaces (FSS), i.e. square patch and single square loop, are considered in this study. Compared to full-wave simulations, the proposed EC model shows more than 95% accuracy. By employing the proposed model and genetic algorithm-based optimization, several designs of broadband absorbers are demonstrated. The presented single- and double-layer FSS show 126% and 161% fractional bandwidth, respectively, with the total thickness close to the Rozanov limit. The results confirm that the proposed method is a simple and efficient way of designing thin wideband absorbers using single-layer or double-layer FSS configurations.
1 January 2013 in Progress in Electromagnetics Research C
A compact dielectric resonator antenna (DRA) for wideband applications is proposed. Two cylindrical dielectric resonators that are asymmetrically located with respect to the center of a rectangular coupling aperture are fed through this aperture. By optimizing the design parameters, an impedance bandwidth of about 29%, covering the frequency range from 9.62 to 12.9 GHz, and a gain of 8 dBi are obtained. Design details of the proposed antenna and the results of both simulation and experiment are presented and discussed.
19 August 2011 in IET Microwaves, Antennas & Propagation
This study reports investigations into phase characteristics of a unit cell of a single-layer microstrip reflectarray exploiting fractal geometries. The aim is to have the phase range larger than 360° accompanied by a smaller slope of the reflected wave phase as a function of the elements' size. These are required to achieve a wide operational bandwidth and a smaller sensitivity to manufacturing errors. To achieve this goal, multi-resonance fractal elements are investigated. It is shown that sliced patches of square and circular shapes as well as multiple rings printed on a thick substrate can offer slower phase slopes while maintaining phase ranges exceeding 360°. The achieved ranges and slopes of these elements are comparable with those of double-stacked patches printed on the equivalent low permittivity dielectric substrate. Choosing suitable dimensions and scaling factors of these elements, the phase characteristic can be made approximately a linear function of their size.