Broadband Power Line communication is considered as one of possible communication technologies for the buildings communication infrastructure in the concept of Smart Building. The possible applications where BPL (Broadband over Power Lines) solution can be used for communication in the concept of Smart Building are Power Quality (PQ) measurement, Electric Vehicle or Micro Grids and Distribution Generation (DG). This article should help to determine clear performance possibilities of BPL for an implementation in Smart Building especially due to a large amount of overhead caused by cybersecurity and the protocol overhead. The possibilities of BPL were measured with five different BPL solutions. The results show a sufficient throughput on the application layer for Smart Building application, because, in the literature, various throughput limits are introduced. According to related work, there are missing measurements on the application layer for laboratory conditions as well as compared with real field measurements. In this article, we also exploit our novel idea of a broadband PLC (Power Line Communication) modem integrated into an electrical outlet.

Building real Smart Metering and Smart Grid networks is very expensive and time-consuming and also it is impossible to install different technologies in the same environment only for comparison. Therefore, simulation and experimental pilot measurements are an easy, economical, and time-affordable solution for a first comparison and evaluation of different technologies and solutions. The local area networks (LAN) are the core of Smart Metering and Smart Grid networks. The two predominant technologies are mostly sufficient for LAN networks, Power Line Communication (PLC), and radio frequency (RF) solutions. For PLC it is hard to allow prediction of the behaviour. Performance assessment for point-to-point connection is easy, but for complex PLC networks with repeaters it is quite expensive. Therefore, a simulation is an easy, fast, and cheap solution for understanding the grid configuration, influence of particular topological components, and performance possibilities. Simulation results can, thus, provide material for the design of a telecommunication infrastructure for Smart Metering. This paper presents results of such a simulation study. It is based on realistic PLC channel model implementation in Network Simulator 3, our modification and extension of this implementation for our use case scenario. It uses Shannon’s formula to calculate theoretical maximum channel capacity. In particular, it provides channel capacity and achievable distances of broadband PLC (BB-PLC). In this article we also exploit our novel idea of simple performance assessment of broadband PLC communication via simulation. It is supposed to be used to understand, evaluate, and test the grid configuration before deployment.

The popularity of the Power Line Communication (PLC) system has decreased due to significant deficiencies in the technology itself, even though new wire installation is not required. In particular, regarding the request for high-speed throughput to fulfill smart-grid requirements, Broadband Power Line (BPLC) can be considered. This paper approaches PLC technology as an object of simulation experimentation in the Broadband Power Line Communication (BPLC) area. Several experimental measurements in a real environment are also given. This paper demonstrates these experimental simulation results as potential mechanisms for creating a complex simulation tool for various PLC technologies focusing on communication with end devices such as sensors and meters. The aim is to demonstrate the potential and limits of BPLC technology for implementation in Smart Grids or Smart Metering applications.

Power line communication (PLC) is considered one of the possible communication technologies for applications in the field of smart metering, smart substations, smart homes, and recently for the management of renewable resources or micro grid control. This article deals with the use of PLC technology to determine the technical condition of the cable. This coefficient can help distribution system operators (DSO) to assess the condition of their cable routes. In this way, possible cable breakdowns and subsequent power outages can be prevented. The resulting methodology for calculating the coefficient is presented in two specific examples of routes, in which a significant benefit for DSO’s can be found.

Broadband over Power Lines (BPL) is considered a promising communication technology in the concept of Smart Grids. This paper evaluates networks based on BPL, with a focus on the impact of repeaters in the linear topology of distribution substations. In large-scale Smart Grids network planning, positions of repeaters have to be carefully chosen. This article should help to determine such positions and limitations of BPL linear topology networks. Laboratory and on-field measurements and their results are presented in this article. Results show the impact of repeater’s deployment for different testing methodologies also with regard to other already presented studies. Measured values and the determined impacts of repeaters are later used as input data for simulation of the linear BPL topology in terms of network throughput with multiple streams and bottlenecks. These occur especially on lines shared by multiple communicating nodes. Furthermore, the simulation investigates the balancing time of multiple data streams throughput. The simulation shows that the throughput balancing can occupy a significant time slot, up to tens of seconds before the throughput of different streams balances. Also, the more data is generated, the more time the balancing time takes. Additionally, the throughput drop caused by a repeater is determined into the range of 35–60%. Based on the measurement and simulation results, lessons learned are presented, and possible performance improvements are discussed.

The article focuses on experimental measurement of multi-carrier narrowband Power Line Communication. The aim of experimental measurements was comparison of multi-carrier narrowband Power Line Communication from the view-point of possible communication distance, available data rate and impact of noise. The specifications G3-PLC and PRIME are considered. The field test results and data rate measurements are presented for different scenarios. They demonstrate consequences of noisy environment and complicated topology. Finally, the article identifies and analysis the fundamental issues for further development of PLC for Smart Grids and Smart Metering.