Alfonso Nájera

Dr. Alfonso Nájera


Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 March 2019 in Metals
Verified
Journal Article
Open access
PDF file
Rodolfo MoralesRodolfo Morales
Rodolfo Morales
JGJavier Guarneros
Javier Guarneros
KCKinnor Chattopadhyay
Kinnor Chattopadhyay
ANAlfonso Nájera
Alfonso Nájera
JRJafeth Rodriguez
Jafeth Rodriguez
The startup of casting sequences in continuous casting of steel using three different turbulence inhibitors were modeled and simulated through the multiphase volume of fluid model (VOF) in a four-strand tundish. In the actual caster, one of the inhibitors released the liquid steel with a superheat high enough to avoid freezing problems in the outer strands. A second inhibitor improved the flow, yet it yielded steel freezing in these strands. A two-phase air–water system was used to model the liquid steel–air system and the interfaces were tracked by a donor–acceptor principle applied in the computational mesh. These activities led to the design of a third inhibitor. Experimental outcomes and the mathematical simulations agreed remarkably well regarding the velocity of the stream front in the tundish floor and the mass of steel reaching the outer strands. A larger steel mass and a faster stream front helped to completely prevent the steel from freezing in the outer strands. Finally, flow fields during the filling of the tundish using two of these inhibitors were simulated and the results explain the different performances observed experimentally.

11 September 2019 in International Journal of Chemical Reactor Engineering
Verified
Journal Article
Closed access
PDF file
OSOscar Joaquin Solis-Marcial
Oscar Joaquin Solis-Marcial
ANAlfonso Nájera
Alfonso Nájera
JBJ. E. Bañuelos
J. E. Bañuelos
OMO. U. Valdés Martínez
O. U. Valdés Martínez
LLL. A. Luevano
L. A. Luevano
Benito Serrano RosalesBenito Serrano Rosales
Benito Serrano Rosales
The dissolution of chalcopyrite under near ambient conditions represents one of the main challenges in the copper industry. Thus, various routes have been proposed for chalcopyrite treatment, such as the use of polar organic solvents, and this has shown promising results. In this paper, we present a study of copper leaching from a chalcopyrite concentrate in aqueous acidic medium with methanol and various H2O2 concentrations at 15, 30, and 40 °C. The results show that nearly complete copper extraction was attained within 5 h at 40 °C. The extraction percentages were plotted as functions of time at each temperature. The experimental data were modeled using the shrinking core model considering the cylindrical particle shape (shrinking cylinder model) within acceptable confidence levels, yielding an estimated activation energy of 24.3 kJ/mol. Furthermore, the process was dependent on the H2O2 concentration, and it acts as a reagent rather than an oxidant in the leaching reaction. It was found that sulfur is the only species present in the solid phase formed during the leaching of chalcopyrite, demonstrating the co-dissolution of both copper and iron.

6 October 2020 in Crystals
Verified
Journal Article
Open access
PDF file
KCKinnor Chattopadhyay
Kinnor Chattopadhyay
Rodolfo MoralesRodolfo Morales
Rodolfo Morales
ANAlfonso Nájera
Alfonso Nájera
JRJafeth Rodriguez
Jafeth Rodriguez
Carlos rodrigo Muñiz ValdezCarlos rodrigo Muñiz Valdez
Carlos rodrigo Muñiz Valdez
Molten steel is alloyed during tapping from the melting furnace to the argon-bottom stirred ladle. The metallic additions thrown to the ladle during the ladle filling time are at room temperature. The melting rates or kinetics of sinking-metals, like nickel, are simulated through a multiphase Euler–Lagrangian mathematical model during this operation. The melting rate of a metallic particle depends on its trajectory within regions of the melt with high or low turbulence levels, delaying or speeding up their melting process. At low steel levels in the ladle, the melting rates are higher on the opposite side of the plume zone induced by the bottom gas stirring. This effect is due to its deviation after the impact of the impinging jet on the ladle bottom. The higher melting kinetics are located on both sides at high steel levels due to the more extensive recirculation flows formed in taller baths. Making the additions above the eye of the argon plume spout increases the melting rate of nickel particles. The increase of the superheat makes the heat flux more significant from the melt to the particle, increasing its melting rate. At higher superheats, the melting kinetics become less dependent on the fluid dynamics of the melt.

2 August 2020 in Metals
Verified
Journal Article
Open access
PDF file
ANAlfonso Nájera
Alfonso Nájera
JRJafeth Rodriguez
Jafeth Rodriguez
JGJavier Guarneros-Guarneros
Javier Guarneros-Guarneros
Rodolfo MoralesRodolfo Morales
Rodolfo Morales
KCKinnor Chattopadhyay
Kinnor Chattopadhyay
Changes of unsteady multiphase fluid flow patterns of liquid steel during electric arc furnace-ladle tapping operations, with simultaneous argon bottom injection, are simulated using interfacial tracking computing techniques. The impinging steel jet interacts with the argon bubbling plume, suffering mutual bending effects, and imparting non-symmetric flows of liquid steel during the whole ladle filling time. At low bath levels, radial recirculating flows are generated and at high bath levels, these flows are substituted by vertical long flows generated by the permanent interaction between the impinging jet and the argon plume. Turbulence intensity increases as the bath level rises. Low bath levels are suitable for pre-melting and preheating ferroalloy particles. High bath levels of steel in the ladle, close to total ladle filling, are the most suitable conditions for thermal and chemical homogenizations. Argon gas forms an intermittent blanket over the air–liquid steel mix due to its higher density than air during the whole ladle filling time.

30 August 2022 in Fluids
Verified
Journal Article
Open access
PDF file
MGM.G. González-Solórzano
M.G. González-Solórzano
Rodolfo MoralesRodolfo Morales
Rodolfo Morales
JGJavier Guarneros
Javier Guarneros
ICIsmael Calderon-Ramos
Ismael Calderon-Ramos
Carlos rodrigo Muñiz ValdezCarlos rodrigo Muñiz Valdez
Carlos rodrigo Muñiz Valdez
ANAlfonso Nájera
Alfonso Nájera
The characterization of the fluid flow of liquid steel in a slab mold, using two nozzle designs under unclogged and clogged conditions, is performed using physical and mathematical simulations. Nozzle A, with an expanding and contracting geometry, yields larger sub-meniscus experimental velocities than nozzle B, with internal flow deflectors. The numerical predictions indicate quick time-changing velocity profiles in the submeniscus region between the mold’s narrow face and the nozzles. The flow deflectors in nozzle B have two effects; the high dissipation rate of kinetic energy in the upper-half length induces lower velocities in the ports than nozzle A. The neutralization of the biased flow caused by the sliding gate allows a balanced fluid through the ports. According to the results, nozzle A yields velocity profiles in the sub-meniscus region with larger standard deviations than nozzle B, leading to an unstable bath surface. The clogged nozzles produced biased-asymmetrical flow patterns in the mold, finding approximated matchings between numerical predictions and experimental measurements. The internal protrusions of the deposits lead to covariance losses of the bath surface wave heights. The use of internal deflectors helped to decrease the amount of clog material in nozzle B.

27 December 2010 in Steel Research International
Verified
Journal Article
Closed access
PDF file
ANAlfonso Nájera
Alfonso Nájera
RMR.D. Morales
R.D. Morales
LGL. García-Demedices
L. García-Demedices
RZR. Zárate-Gutiérrez
R. Zárate-Gutiérrez
JRJ. Rodríguez-Ávila
J. Rodríguez-Ávila