Fawad Maqbool

Fawad Maqbool


Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 May 2019 in Materials
Verified
Journal Article
Open access
PDF file
RHRamin Hajavifard
Ramin Hajavifard
FMFawad Maqbool
Fawad Maqbool
ASAnke Schmiedt-Kalenborn
Anke Schmiedt-Kalenborn
JBJohannes Buhl
Johannes Buhl
MBMike Bambach
Mike Bambach
Frank WaltherFrank Walther
Frank Walther
Disc springs are conical annular discs, which are characterized by a high spring force with a small spring travel and good space utilization. In operation, they must meet high demands on the stability of the spring characteristic and the fatigue strength. Under loading, tensile stresses occur which limit the possible applications of disc springs. Compressive stresses can be generated in the stressed areas by means of shot-peening in order to extend the operating limits for a given yield and fatigue strength. Since the spring geometry and characteristics change during shot-peening, the design of the shot-peening treatment is iterative and cumbersome. The present research proposes an incremental forming process for forming and integrated targeted adjustment of residual stresses in disc springs from metastable austenitic stainless steel (MASS), to achieve improved spring properties and high cyclic strength. The main mechanism of residual stress generation is the transformation of metastable austenite into martensite under the action of the forming tool. Different experimental characterization techniques like the hole drilling method, X-ray diffraction, disc compression tests, optical microscopy and cyclic tests are used to correlate the residual stresses and disc spring properties. A numerical model is developed for simulating the martensite transformation in disc springs manufacturing. The results prove that incremental forming enables process-integrated engineering of the desired compressive residual stresses, entailing a higher spring force of metastable austenitic disc springs in comparison to conventional disc springs. Due to martensite formation, the generated residual stresses are stable under cyclic loading, which is not the case for conventionally manufactured springs.

Verified
Journal Article
Open access
PDF file
FMFawad Maqbool
Fawad Maqbool
MBMike Bambach
Mike Bambach
The aim of this study is to analyze the co-relation between the geometrical accuracy of parts formed by single-point incremental forming (SPIF) and the resulting distribution of the residual stresses induced in the material as a function of the different process parameters of the SPIF process. The study was performed for a pyramidal frustum manufactured by varying the process parameters of SPIF, i.e., tool diameter, tool step-down, and wall-angle. The hole-drilling strain gage method was used to determine the residual stresses in the manufactured pyramids. Further, small strips were laser cut from the pyramids, and the curvature of the strips was measured. The curvature of the strips is a result of the intensity and distribution of the residual stresses, which in turn depends on the selected values of the process parameters. A validated numerical model of SPIF was used to determine the residual stresses parallel and perpendicular to the direction of tool motion at the center of a strip cut from the numerical model in clamped, unclamped, and trimmed states. Further, the change in the bending moment of a strip that occurred upon unclamping and trimming was calculated. Experimental and numerical investigations reveal that the most significant parameter in residual stress build-up and the reduction of geometrical accuracy is the wall angle. Upon unclamping, the highest change in the residual stresses and bending moment occurred with the largest tool step-down and tool diameter. Upon trimming, the magnitude of the residual stresses and bending moment changed the most with the largest tool step-down in both directions, whereas the change was highest with the smallest tool diameter in the transverse direction of the tool motion. Furthermore, upon trimming, the geometric deviations were highest with the large wall angles in the transverse direction of the tool motion. Overall, the effect of changing process parameters on the residual stress state and geometrical accuracy was more pronounced in the transverse direction of the tool motion.

3 May 2021 in Archive of Applied Mechanics
Verified
Journal Article
Open access
PDF file
FMFawad Maqbool
Fawad Maqbool
FMFabian Maaß
Fabian Maaß
JBJohannes Buhl
Johannes Buhl
MHMarlon Hahn
Marlon Hahn
RHRamin Hajavifard
Ramin Hajavifard
MBMike Bambach
Mike Bambach
The mechanical properties and the operating life of a formed component are highly dependent on the residual stress state. There is always a high magnitude of residual stresses in the components formed by incremental sheet forming (ISF) due to the localized deformation mechanism. Hence, a thorough understanding of the generation of the residual stresses by ISF is necessary. This study investigates the residual stress generation mechanism for two process variants of ISF, i.e., Single Point Incremental Forming (SPIF) and Two Point Incremental Forming (TPIF). This understanding is used to control and targetedly generate the residual stresses to improve the part performance. In this regard, the residual stress state in a truncated cone geometry manufactured using SPIF and disc springs manufactured using TPIF was experimentally analyzed. Validated numerical models for both process variants were developed to study the residual stresses in detail. The residual stress state in SPIF is such that the tool contact side develops tensile residual stresses and the non-contact side undergoes compressive residual stresses. The tool step-down variation was used to control residual stresses and improve the fatigue strength of truncated cones manufactured using SPIF. For TPIF, two different forming strategies were used to analyze the residual stress generation mechanism and the role of major process parameters. The residual stresses for TPIF are pre-dominantly compressive in both directions of forming tool motion. For both process variants of the ISF process, it is shown that the residual stresses can be beneficially utilized to improve mechanical properties of the components.

5 December 2018 in Production Engineering
Verified
Journal Article
Closed access
PDF file
FMFawad Maqbool
Fawad Maqbool
RHRamin Hajavifard
Ramin Hajavifard
Frank WaltherFrank Walther
Frank Walther
MBMike Bambach
Mike Bambach

1 January 2017 in AIP Conference Proceedings
Verified
Conference Paper
Closed access
FMFawad Maqbool
Fawad Maqbool
MBMike Bambach
Mike Bambach
Incremental sheet forming (ISF) is a manufacturing process most suitable for small-batch production of sheet metal parts. In ISF, a CNC-controlled tool moves over the sheet metal, following a specified contour to form a part of the desired geometry. This study focuses on one of the dominant process limitations associated with the ISF, i.e., the limited geometrical accuracy. In this regard, a case study is performed which shows that increased geometrical accuracy of the formed part can be achieved by a using stress-relief annealing before unclamping. To keep the tooling costs low, a modular die design consisting of a stiff metal frame and inserts made from inexpensive plastics (Sika®) were devised. After forming, the plastics inserts are removed. The metal frame supports the part during stress-relief annealing. Finite Element (FE) simulations of the manufacturing process are performed. Due to the residual stresses induced during the forming, the geometry of the formed part, from FE simulation and the actual manufacturing process, shows severe distortion upon unclamping the part. Stress relief annealing of the formed part under partial constraints exerted by the tool frame shows that a part with high geometrical accuracy can be obtained.

1 January 2016 in AIP Conference Proceedings
Verified
Conference Paper
Closed access
FMFawad Maqbool
Fawad Maqbool
LELars Elze
Lars Elze
HSHolger Seidlitz
Holger Seidlitz
MBMike Bambach
Mike Bambach
Sandwich materials made from corrugated sheet metal provide excellent mechanical properties for lightweight design without using filler material. The increased mechanical properties of these sandwich materials are achieved by the 3-D geometry of the corrugated sheet and the hardening due to pre-forming. In the present study, manufacturing of corrugated sheet metal consisting of hexagonal bulge patterns through hydroforming and incremental forming is analyzed. Double layered corrugated sheet metal sandwiches with hexagonal patterns of free-form bulge geometries are investigated through finite element analysis for the maximum increase in stiffness over the normal flat sheets. The analysis shows that a bending stiffness increase of up to 13 times over flat sheet of the same mass is attainable by corrugated sandwiches. Further, it is proved for these types of corrugation sandwiches that stiffness increases by increasing the height of the corrugation bulge but that hydroforming poses restrictions with respect to bulge height, since it is limited by forming force and formability of the material. Incremental sheet metal forming can be used to produce sheets with a hexagonal bulge pattern with increased height. Hence, a higher increase in stiffness as compared to hydroforming is possible but at the expense of process speed.