Ramin Hajavifard

Mr. Ramin Hajavifard

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 May 2019 in Materials
Verified
Journal Article
Open access
PDF file
RHRamin Hajavifard
Ramin Hajavifard
FMFawad Maqbool
Fawad Maqbool
ASAnke Schmiedt-Kalenborn
Anke Schmiedt-Kalenborn
JBJohannes Buhl
Johannes Buhl
MBMike Bambach
Mike Bambach
Frank WaltherFrank Walther
Frank Walther
Disc springs are conical annular discs, which are characterized by a high spring force with a small spring travel and good space utilization. In operation, they must meet high demands on the stability of the spring characteristic and the fatigue strength. Under loading, tensile stresses occur which limit the possible applications of disc springs. Compressive stresses can be generated in the stressed areas by means of shot-peening in order to extend the operating limits for a given yield and fatigue strength. Since the spring geometry and characteristics change during shot-peening, the design of the shot-peening treatment is iterative and cumbersome. The present research proposes an incremental forming process for forming and integrated targeted adjustment of residual stresses in disc springs from metastable austenitic stainless steel (MASS), to achieve improved spring properties and high cyclic strength. The main mechanism of residual stress generation is the transformation of metastable austenite into martensite under the action of the forming tool. Different experimental characterization techniques like the hole drilling method, X-ray diffraction, disc compression tests, optical microscopy and cyclic tests are used to correlate the residual stresses and disc spring properties. A numerical model is developed for simulating the martensite transformation in disc springs manufacturing. The results prove that incremental forming enables process-integrated engineering of the desired compressive residual stresses, entailing a higher spring force of metastable austenitic disc springs in comparison to conventional disc springs. Due to martensite formation, the generated residual stresses are stable under cyclic loading, which is not the case for conventionally manufactured springs.

3 May 2021 in Archive of Applied Mechanics
Verified
Journal Article
Open access
PDF file
FMFawad Maqbool
Fawad Maqbool
FMFabian Maaß
Fabian Maaß
JBJohannes Buhl
Johannes Buhl
MHMarlon Hahn
Marlon Hahn
RHRamin Hajavifard
Ramin Hajavifard
MBMike Bambach
Mike Bambach
The mechanical properties and the operating life of a formed component are highly dependent on the residual stress state. There is always a high magnitude of residual stresses in the components formed by incremental sheet forming (ISF) due to the localized deformation mechanism. Hence, a thorough understanding of the generation of the residual stresses by ISF is necessary. This study investigates the residual stress generation mechanism for two process variants of ISF, i.e., Single Point Incremental Forming (SPIF) and Two Point Incremental Forming (TPIF). This understanding is used to control and targetedly generate the residual stresses to improve the part performance. In this regard, the residual stress state in a truncated cone geometry manufactured using SPIF and disc springs manufactured using TPIF was experimentally analyzed. Validated numerical models for both process variants were developed to study the residual stresses in detail. The residual stress state in SPIF is such that the tool contact side develops tensile residual stresses and the non-contact side undergoes compressive residual stresses. The tool step-down variation was used to control residual stresses and improve the fatigue strength of truncated cones manufactured using SPIF. For TPIF, two different forming strategies were used to analyze the residual stress generation mechanism and the role of major process parameters. The residual stresses for TPIF are pre-dominantly compressive in both directions of forming tool motion. For both process variants of the ISF process, it is shown that the residual stresses can be beneficially utilized to improve mechanical properties of the components.