This paper presents new Wide Bandpass Filter (WBPF) and Narrow Bandstop Filter (NBSF) incorporating two microstrip resonators, each resonator is based on 2nd iteration of Hilbert fractal geometry. The type of filter as pass or reject band has been adjusted by coupling gap parameter (d) between Hilbert resonators using a substrate with a dielectric constant of 10.8 and a thickness of 1.27 mm. Numerical simulation results as well as a parametric study of d parameter on filter type and frequency responses are presented and studied. WBPF has designed at resonant frequencies of 2 and 2.2 GHz with a bandwidth of 0.52 GHz, −28 dB return loss and −0.125 dB insertion loss while NBSF has designed for electrical specifications of 2.37 GHz center frequency, 20 MHz rejection bandwidth, −0.1873 dB return loss and 13.746 dB insertion loss. The proposed technique offers a new alternative to construct low-cost high-performance filter devices, suitable for a wide range of wireless communication systems.
In this paper, a new bandpass filter design has been presented using simple topology of stepped impedance square loop resonator. The proposed bandpass filter has been simulated and fabricated using a substrate with an insulation constant of 10.8, thickness of 1.27mm and loss tangent of 0.0023 at center frequency of 5.8 GHz. The simulation results have been evaluated using Sonnet simulator that is extensively adopted in microwave analysis and implementation. The output frequency results demonstrated that the proposed filter has high-quality frequency responses in addition to isolated second harmonic frequency. Besides, this filter has very small surface area and perceptible narrow band response features that represent the conditions of recent wireless communication systems. Various filter specifications have been compared with different magnitudes of perturbation element dimension. Furthermore, phase scattering response and current intensity distribution of the proposed filter have been discussed. The simulated and experimental results are well-matched. Lastly, the features of the proposed filter have been compared with other designed microstrip filters in the literature.
28 October 2014 in International Journal of Electronics
This paper presents new microstrip bandpass filter design topologies that consist of dual edge-coupled resonators constructed in the form of Moore fractal geometries of second and third iteration levels. The space-filling property for proposed fractal filters has found to produce reduced size shapes in accordance with sequential iteration levels. These filters have been prepared for ISM band applications at a centre frequency of 2.4 GHz using a substrate with a dielectric coefficient of 10.8, dielectric thickness of 1.27 mm and metallisation thickness of 35 µm. The output responses of each fractal bandpass filter have been determined by a full-wave-based electromagnetic simulator Sonnet software package. Simulated and experimental results are approximately compatible with each other. These responses clarify that these fractal filters have good transmission and return loss characteristics with blocked higher harmonics in out-of-band regions.
8 December 2014 in International Journal of Microwave and Wireless Technologies
Fractal geometries are attractive for antenna designers seeking antennas with compact size and multiband resonant behavior. This paper presents the design of a new microstrip-fed printed slot antenna for use in dual-band wireless applications. The slot structure of the proposed antenna is in the form of Cantor square fractal geometry of the second iteration. The slot structure has been etched on the ground plane of a substrate with relative permittivity of 4.4 and 1.6 mm in thickness. A parametric study is conducted to explore the effects of some geometrical parameters on the antenna performance. Results show that the antenna possesses a dual-band behavior with a wide range of resonant frequency ratio. In addition to the ease of fabrication and simple design procedure, the antenna offers desirable radiation characteristics. A prototype of the proposed antenna has been simulated, fabricated, and measured. The measured 10 dB return loss bandwidths for the lower and the upper resonant bands are 42% (2.35–3.61 GHz) and 20% (5.15–6.25 GHz), respectively. This makes the proposed antenna suitable to cover a number of operating bands of wireless systems (2.4 GHz-Bluetooth, 2.4 GHz ISM, 2.4/5.8 GHz-WLAN, 3.5 GHz-WiMAX, and 5.8 GHz-ITS).
A new compact printed monopole antenna is presented in this paper. An open-loop hexagonal radiator excited by a microstrip feed line, which is printed on top of the substrate, which is FR4 type, while on another side, a partial ground plane is fixed and embedded with two pairs of slits as well as a pair of rectangular strips. Triple operating bands with two different polarization types are obtained. The lower band has right-hand circular polarization (RHCP) characteristic, whereas the upper band has left-hand circular polarization (LHCP) characteristic means that a dual-band dual-sense circular polarization (CP). Concerning the middle band, a linear polarization (LP) has been gotten in this antenna. Numerical analysis and experimental validation of the proposed antenna structure have been performed, and results are demonstrated. The measured impedance bandwidths (IBWs) are 14.7% (1.478-1.714 GHz), 6.8% (2.54-2.72 GHz), and 13.1% (4.29-4.89 GHz), respectively. The measured 3-dB axial ratio bandwidths (ARBWs) are 6.2% (1.510-1.606 GHz), and 22.7% (4.035-5.07 GHz) for the lower and the upper band, respectively. So, it's suitable for covering modern wireless applications such as GPS (Global Positioning System), LTE (Long Term Evaluation), and Satellite.
22 October 2018 in Wireless Personal Communications