This paper presents the detailed design, analysis, and application of the controller for a shunt active power filter based on a pulsewidth modulation dc-to-ac voltage source converter. The controller is mainly tailored to compensate harmonic currents of nonlinear loads connected to the mains. However, it can also achieve reactive-power compensation and mains-current balancing when required. The controller has a two-layer structure. The outer layer generates the current references for the inner layer. The former uses a plug-in discrete-time repetitive algorithm for current-harmonic compensation, a proportional-integral algorithm to maintain the dc-capacitor voltage in spite of unmodeled losses and a reactive-power-reference generator. The inner layer uses state-feedback with integral action for current control. The repetitive controller is justified to improve the tracking of the periodic current references required by the active filters. The stability of the resulting closed-loop system is studied and some indication of the system robustness is given. The proposed controller has been tested in a prototype with balanced and unbalanced nonlinear loads. A discrete-time model of the filter has been used from the beginning. The microcomputer delay when calculating the controller output and the delay due to the anti-aliasing filters have been included in the inner system state-variable model

This paper presents a generalized d-q loss model applicable to permanent-magnet synchronous motors, synchronous reluctance motors, induction motors and DC motors. This model is used as the basis of a loss-minimization expression of easy implementation. Core saturation is taken into account. The paper reviews model-based loss-minimization schemes previously presented in the literature for specific types of motors. It shows how all these loss models can be derived from the general one proposed here. The results using the loss-minimization expression in specific motors are compared to those previously reported in the literature. Finally, experimental results for an interior permanent-magnet synchronous motor are presented to validate the applicability of the proposed expression

This paper presents a control system based on a repetitive controller to compensate for key power-quality disturbances, namely voltage sags, harmonic voltages, and voltage imbalances, using a dynamic voltage restorer (DVR). The control scheme deals with all three disturbances simultaneously within a bandwidth. The control structure is quite simple and yet very robust; it contains a feedforward term to improve the transient response and a feedback term to enable zero error in steady state. The well-developed graphical facilities available in PSCAD/EMTDC are used to carry out all modeling aspects of the repetitive controller and test system. Simulation results show that the control approach performs very effectively and yields excellent voltage regulation.

Multi-terminal High Voltage Direct Current (HVDC) using Voltage Source Converters (VSC-HVDC) is a promising technology which provides flexible control of active and reactive power and facilitates remote renewable energy integration, above all using long cables. This paper analyses an active power control strategy for multi-terminal VSC-HVDC systems tailored to enhance transient stability of hybrid AC/DC grids. The proposed strategy controls each VSC using frequency measurements of all terminals. Its performance is compared to a strategy in which each VSC is controlled using only local frequency measurements of the AC side, proving that the proposed strategy shows better performance, even taking into account reasonable communication delays. The paper also shows that the proposed strategy generally gives similar results to those obtained when each VSC is controlled using the speed of the centre of inertia (COI). The speed of the COI is a more comprehensive and richer figure than the one proposed in this paper but it is also much more complex to obtain. Simulation results with PSS/E of a test system have been used to illustrate the comparisons and the main contributions of the proposal.

The always-increasing switching frequency of modern solid-state power switches, together with the application of multi-converter topologies, make it possible to use pulse width modulation (PWM) in high power applications of STATCOMs (static synchronous compensators). This paper investigates the control system for a PWM-based STATCOM. First of all, a discrete-time model of the STATCOM is derived to take into account the discrete-time implementation of the controller. Secondly, the control algorithm is detailed. It ensures decoupled control of the real and reactive power exchanged between the power converter and the electric-energy system. This is necessary to control the DC capacitor voltage during transients of the exchanged reactive power. Finally, the control of the capacitor voltage is explained in detail. The controller is tailored to keep the capacitor voltage almost constant in spite of the fast control of the reactive power. This helps to reduce the capacitor size significantly. The main contributions are illustrated using a 15 kVA laboratory prototype.