As a kind of high explosives, aluminized explosive cannot release the energy maximumly, which is a key problem. Using DTA‐TG equipment, the ignition performance of three kinds of aluminized explosives (RDX, HMX, and CL‐20) with different mass percentages of aluminum powder (0%, 10 wt.%, 20 wt.%, and 30 wt.%) was investigated. The results showed that the energy release of the HMX/Al composite explosive with 10 wt.%, 20 wt.%, and 30 wt.% aluminum powder was only equivalent to 80%, 65%, and 36% of pure HMX, respectively. It was similar to RDX/Al and CL‐20/Al composite explosives, except the CL‐20/Al mixture with 10% aluminum powder. Rather than participating in the ignition and combustion, the aluminum powder does effect the complete reaction of RDX, HMX, and CL‐20 in the initial stage of ignition or in the lower temperature area of the boundary.
18 September 2019 in Journal of Energetic Materials
Nano-sized aluminum powders (n-Al) are usually added to high energy explosives and propellants o promote their detonation and combustion performance. From the perspective of thermal safety, this work focused on the thermal decomposition and explosion properties of CL-20 in the absence and presence of 30 wt% n-Al (CL-20/n-Al). The results of DSC experiments showed that the activation energy ( ) of thermal decomposition of CL-20 slightly decreased upon addition of n-Al, implying that n-Al exhibited a certain degree of catalytic effect on the thermal decomposition process of CL-20, but the catalytic activity is quite low. By nonlinear multivariate regression method, the kinetic model for the thermal decomposition of CL-20 and CL-20/n-Al was determined as n-th order reaction with autocatalysis, and both the reaction order (n) and autocatalytic kinetic rate constant ( ) of CL-20 were found to be lower than those of CL-20/n-Al, indicating that the complexity of the decomposition reaction system and autocatalytic ability of CL-20 during thermal decomposition increased upon addition of n-Al. By the deflagration point tests, the Five-Second explosion temperature ( ) of CL-20 and CL-20/n-Al was determined to be 277.7°C and 282.3°C, respectively. Moreover, the activation energy ( ) of thermal explosion of CL-20 and CL-20/n-Al were calculated as 159.98 kJ mol−1 and 100.7 kJ mol−1, respectively. From the more than one-third reduction of value, it can be concluded that the thermal sensitivity of CL-20 explosive could be remarkably decreased by adding n-Al, especially under the low-temperature condition.
16 December 2020 in Journal of Energetic Materials
This work developed a method for calculating the Jones-Wilkins-Lee (JWL) equation of state (EOS) for the detonation products of aluminized explosives based on hexanitrohexaazaisowurtzitane (CL-20). On the basis of previous studies, chemical reaction equations, Hess’ law and Avogadro’s law were all incorporated in this process because of the non-ideal detonations of aluminized explosives. The EOS parameters were determined for explosive formulations comprising pure CL-20 as well as aluminized versions and compared to literature reports. Calculated pressure-specific volume curves were in good agreement with prior studies. A 50 mm cylinder test using a CL-20/Al/wax composition with a 75/20/5 mass ratio was conducted and the calculated EOS parameters were used to simulate the expansion of the cylinder wall. The experimental and simulation plots were found to agree within 5%, which confirms the validity of this method with regard to engineering analyses.
14 September 2020 in Propellants, Explosives, Pyrotechnics
DSC experiments were conducted on the 2,4,6,8,10,12-hexanitro-2,4,6,8,10,12-hexaaza-tetracyclo-[5.5.0.05,9.03,11]-dodecane (also known as HNIW or CL-20) and CL-20 containing 10 wt.% microsized aluminum (Al) powders. The kinetic parameters of CL-20 and CL-20/Al were obtained by ASTM685 and Friedman methods, respectively, indicating that Al powder decreases the activation energy of CL-20 slightly and has a catalytic effect on the thermal decomposition of CL-20. By the method of nonlinear multivariate regression, kinetic models of CL-20 and CL-20/Al were derived as , where the of CL-20 and CL-20/Al is 1.97 and 2.12, respectively, showing that the autocatalytic ability of CL-20 had been increased by adding Al powder. From the SEM images of CL-20/Al and the XRD pattern of the decomposition residues of CL-20/Al, it can be inferred that partial combustion of Al particles happened in the microscale view and led to the release of heat.