Vehicle sideslip angle can be estimated using either dynamic or kinematic models. The dynamic model requires vehicle parameters, which might have uncertainties due to different load conditions, vehicle motions, and road frictions. Parameter uncertainties might result in estimation errors. Thus system identifications are required to estimate those parameters online. On the other hand, the kinematic model does not require these parameters. A closed-loop estimator can be formulated to estimate the sideslip angle using the kinematic model. Since the system matrix which consists of the yaw rate is time varying, the required input vector and output contain process and measurement noises, respectively, and the disturbance input matrix contains estimated states, extended Kalman filter is used to obtain the estimation gain in this paper. CarSim is used to evaluate the proposed approach under different driving scenarios and road frictions in Matlab/Simulink. The preliminary results show promising improvement of the sideslip angle estimation.
28 May 2014 in International Journal of Automotive Technology
A sliding-mode controller (SMC) is proposed for semi-active suspensions to achieve ride comfort and handling performance simultaneously. First, a nonlinear quarter-car model of Macpherson strut suspension is established in Matlab/Simulink. Constrained damper force and actuator dynamics are considered for the damper model. System identification is applied to the nonlinear model for obtaining the linear model parameters. Kalman filter is designed based on the linear model and the actuator dynamics to estimate the state responses required for SMC. The sliding surface consists of tyre deflection and sprung mass acceleration. The proposed SMC is evaluated using the nonlinear model for both time and frequency domain responses. Robustness due to the increased sprung mass and deteriorated suspension is also investigated in this paper. Preliminary simulation results show improved ride comfort without sacrificing the road holding performance.
19 October 2004 in Journal of Dynamic Systems, Measurement, and Control
A Time-To-Rollover (TTR) metric is proposed as the basis to assess rollover threat for an articulated heavy vehicle. The TTR metric accurately “counts-down” toward rollover regardless of vehicle speed and steering patterns, so that the level of rollover threat is accurately assessed. There are two conflicting requirements in the implementation of TTR. On the one hand, a model significantly faster than real-time is needed. On the other hand, the TTR predicted by this model needs to be accurate enough under all driving scenarios. An innovative approach is proposed in this paper to solve this dilemma and the design process is illustrated in an example. First, a simple yet reasonably accurate yaw∕roll model is identified. A Neural Network (NN) is then developed to mitigate the accuracy problem of this simple model. The NN takes the TTR generated by the simple model, vehicle roll angle, and change of roll angle to generate an enhanced NN-TTR index. The NN was trained and verified under a variety of driving patterns. It was found that an accurate TTR is achieved across all the driving scenarios we tested.
The cruising distance of the range extended electric vehicle (REEV) can be further extended using a range extender, which consists of an engine and a generator, i.e., a genset. An adaptive power management strategy (PMS) based on the equivalent fuel consumption minimization strategy (ECMS) is proposed for the REEV in this paper. The desired trajectory of the state of charge (SOC) is designed based on the energy-to-distance ratio, which is defined as the difference between the initial SOC and the minimum allowable SOC divided by the remaining travel distance, for discharging the battery. A self-organizing fuzzy controller (SOFC) with SOC feedback is utilized to modify the equivalence factor, which is defined as the fuel consumption rate per unit of electric power, for tracking the desired SOC trajectory. An instantaneous cost function, that consists of the fuel consumption rate of the genset and the equivalent fuel consumption rate of the battery, is minimized to find the optimum power distribution for the genset and the battery. Dynamic programming, which is a global minimization method, is employed to obtain the performance upper bound for the target REEV. Simulation results show that the proposed algorithm is adaptive for different driving cycles and can effectively increase the fuel economy of the thermostat control strategy (TCS) by 11.1% to 16%. The proposed algorithm can also reduce average charging/discharging powers and low SOC operations for possibly extending the battery life and increasing the battery efficiency, respectively. An experiment of the prototype REEV on a chassis dynamometer is set up with the proposed algorithm implemented on a real-time controller. Experiment results show that the proposed algorithm can increase the fuel economy of the TCS by 7.8% for the tested driving cycle. In addition, the proposed algorithm can reduce the average charge/discharge powers of TCS by 7.9% and 11.7%, respectively.
Steering has more potential than braking to prevent rear-end collisions at higher relative velocities. A path tracking controller based on multi-input multi-output (MIMO) model predictive control (MPC) is proposed to enhance the handling performance of autonomous emergency steering in this paper. A six-state MIMO bicycle model including actuator dynamics of steering and differential braking is used for model prediction. Two control inputs are front wheel steering angle and direct yaw moment. Two model outputs are lateral displacement and heading angle. According to the work load ratios at four wheels, control allocation is used to determine the optimal braking force distribution to prevent tire force saturation. The performance of a single-input single-output (SISO) MPC that uses only steering angle control to track the lateral displacement of the desired path is employed to benchmark the performance of the proposed algorithm. Simulation results show that both SISO MPC and MIMO MPC can track the path on nominal road surface with high road friction coefficient of 0.9. For a road surface with medium road friction coefficient of 0.7, the SISO MPC is unable to track the path and loses directional stability. However, the MIMO MPC can still track the path and demonstrate robust path tracking and handling enhancement against model uncertainty due to reduced road friction.