Terahertz (THz) communication is a promising technique for chip-to-chip communication and wireless personal area networks. In this paper, we present an experimental study and design to realize such THz communication systems. We develop two different chip sets for on-off-keying (OOK) modulation based THz transceivers which include carrier generators, modulators, THz amplifiers, and baseband amplifiers. Specifically, the first chip set integrates the circuit blocks for the OOK modulation without the THz amplifier for short-range communication. In addition, the second chip set design includes the THz amplifier modules to extend the coverage of transmission. For these two chip sets, we experimentally demonstrate the feasibility of the wireless communication at THz frequency bands and assess performance using the bit error rate (BER) analysis. We estimate the BER by calculating the signal-to-noise ratio (SNR) based on the eye diagram and compare with actual BER measurements and Monte Carlo simulations. We also address the impact of the distance, the transmit power, and the data rate for the proposed THz transceivers based on the link budget analysis, and confirm the accuracy of the derived BER expression.
1 November 2020 in IEEE Transactions on Microwave Theory and Techniques
This article presents W- and G-band voltage-controlled oscillators (VCOs) fabricated in a 60 nm GaN high electron-mobility transistor (HEMT) process with f T /f MAX of 190/250 GHz. Two W-band fundamental VCOs (VCO1 and VCO2) are designed without and with a varactor, respectively. In addition, a G-band push-push VCO (VCO3) is designed to demonstrate feasibility of a GaN power source in the sub-terahertz band. The measurement shows that VCO1 and VCO2 exhibit output power of 22.5 and 22.6 dBm and dc-to-RF efficiency of 14.7% and 16.8% at 87.5 and 86.5 GHz, respectively. The power and efficiency are the highest values among the previously reported GaN VCOs operating beyond 50 GHz. Furthermore, VCO2 achieves a wide tuning range of 9.0 GHz (77.5-86.5 GHz). The VCO3 exhibits high output power of 9.3 dBm at 180.6 GHz. To the best of the authors' knowledge, this is the first demonstration of a G-band VCO in a GaN technology. The W- and G-band VCOs occupy compact chip areas of 0.48 and 0.32 mm 2 , respectively.
27 May 2019 in IEEE Transactions on Microwave Theory and Techniques
This paper presents a 300-GHz voltage-controlled oscillator (VCO) with a wide frequency tuning range and high output power. To generate fundamental oscillation at 300 GHz, a cascode cross-coupled pair is employed as a VCO core instead of a conventional common-emitter pair. Capacitive emitter degeneration is added to the VCO core to achieve a wide bandwidth of a negative conductance. In addition, the phase of the oscillation feedback loop is analyzed and optimized to further extend the tuning range. The VCO is fabricated in a 0.25-μm InP DHBT technology ( f T /f max = 392/859 GHz). Measurements show that the VCO frequency is tuned from 272.4 to 310.8 GHz with a peak output power of 1.5 dBm. To the best of authors' knowledge, this is the widest tuning range of 38.4 GHz (a fractional bandwidth of 13.2%) among the reported fundamental VCOs at the WR-3 band.
17 May 2012 in IEEE Microwave and Wireless Components Letters
A harmonic-tuned high efficiency oscillator is designed using gallium nitride (GaN) high electron mobility transistors (HEMTs). The harmonic load-pull simulation is performed to find the voltage and current waveforms and to locate the optimum load impedance for high efficiency operation of the transistor. Then, the feedback network for the oscillation is synthesized based on the load-pull data. The series resonant circuit is employed in the feedback network to provide open circuit to the load network at harmonic frequencies. Therefore, the load network can be designed separately from the feedback network to present the optimum harmonic load impedances. In this way, the transistor in the oscillator can achieve the optimum voltage and current waveforms determined by the harmonic load-pull simulation. The fabricated GaN oscillator using the proposed design approach shows the maximum efficiency of 80.2% and output power of 35.1 dBm at 2.42 GHz under drain bias voltage of 22 V.
A D-band on–off keying (OOK) transceiver chipset is fabricated in a 65-nm bulk CMOS technology as a low-cost and highly integrative solution to short-distance wireless connectivity. Supplementary transistor modeling is performed for accurate circuit design at mm-wave frequencies. To overcome low transistor $\text{f}_{\mathrm {max}}$ and reduce dc power consumption, the transmitter employs a frequency-multiplier-based architecture with no power amplifier. The receiver adopts a non-coherent architecture consisting of a dc-coupled three-stage differential amplifier and an envelope detector. The OOK transmitter exhibits a measured output power of −9.8 dBm and an on–off level difference of 13.2 dB at 134.1 GHz. The receiver shows a measured average responsivity of 4.1 kV/W and a noise equivalent power of 211.4 pW/Hz 1/2 over all D-band frequencies. The dc power consumption of the transmitter and the receiver is 76 and 32.5 mW, respectively. The transceiver is tested in both on-chip loopback and air-channel configurations and demonstrates data transmission up to 10 and 2 Gb/s at a distance of 0.03 m, respectively.