We present a novel hybrid glass-polymer micromechanical sensor by combining two femtosecond laser direct writing processes: laser illumination followed by chemical etching of glass and two-photon polymerization. This incorporation of techniques demonstrates the capability of combining mechanical deformable devices made of silica with an integrated polymer structure for passive chemical sensing application. We demonstrate that such a sensor could be utilized for investigating the elastic properties of polymeric microstructures fabricated via the two-photon polymerization technique. Moreover, we show that polymeric microstructure stiffness increases when immersed in organic liquids.
In this work, a burst mode laser is used for micromachining of 20 µm–250 µm thick Invar (Fe64/Ni36) foils. Holes were drilled by firing multiple pulses transversely onto the sample without moving the beam (percussion drilling). The utilized laser system generates a burst of a controllable number of pulses (at 1030 nm) with tunable pulse-to-pulse time spacing ranging from 200 ps to 16 ns. The sub-pulses within the burst have equal amplitudes and a constant duration of 300 fs that do not change regardless of the spacing in time between them. In such a way, the laser generates GHz to MHz repetition rate pulse bursts with a burst repetition rate ranging from 100 kHz to a single shot. Drilling of the material is compared with the non-burst mode of kHz repetition rate. In addition, we analyze the drilling speed and the resulting dependence of the quality of the holes on the number of pulses per burst as well as the average laser power to find the optimal micromachining parameters for percussion drilling. We demonstrate that the micromachining throughput can be of an order of magnitude higher when using the burst mode as compared to the best results of the conventional kHz case; however, excess thermal damage was also evident in some cases.
Transparent and high-hardness materials have become the object of wide interest due to their optical and mechanical properties; most notably, concerning technical glasses and crystals. A notable example is sapphire—one of the most rigid materials having impressive mechanical stability, high melting point and a wide transparency window reaching into the UV range, together with impressive laser-induced damage thresholds. Nonetheless, using this material for 3D micro-fabrication is not straightforward due to its brittle nature. On the microscale, selective laser etching (SLE) technology is an appropriate approach for such media. Therefore, we present our research on C-cut crystalline sapphire microprocessing by using femtosecond radiation-induced SLE. Here, we demonstrate a comparison between different wavelength radiation (1030 nm, 515 nm, 343 nm) usage for material modification and various etchants (hydrofluoric acid, sodium hydroxide, potassium hydroxide and sulphuric and phosphoric acid mixture) comparison. Due to the inability to etch crystalline sapphire, regular SLE etchants, such as hydrofluoric acid or potassium hydroxide, have limited adoption in sapphire selective laser etching. Meanwhile, a 78% sulphuric and 22% phosphoric acid mixture at 270 °C temperature is a good alternative for this process. We present the changes in the material after the separate processing steps. After comparing different processing protocols, the perspective is demonstrated for sapphire structure formation.
Femtosecond lasers are widely applied in scientific and industrial fields. Recent trends in the laser market show decreasing prices for femtosecond units, which will ultimately lead to the opening of new markets that were inaccessible in the past due to the high costs of such systems. To this end, new techniques that enable micromachining of materials with increased efficiency are interesting. In this article, we demonstrate a technique that may be used for cutting and drilling various materials. By placing a layer of water on top of the samples and loosely focusing laser light on the surface, it was found that the micromachining throughput is increased by up to 10-fold as compared with micromachining without the water layer (conventional focusing in air), however, the main reasons for the increase in fabrication efficiency have not been fully understood until now. By modelling the propagation of the femtosecond pulses by means of the nonlinear modified Schrodinger equation through the water layer, we show that the increased throughput is attributed to the changing of the Gaussian intensity profile. In addition, we confirm these findings by numerically modelling the ablated crater formation.
Femtosecond laser-assisted material surface modification is a rapidly growing field with numerous applications, including tribology, micromechanics, optofluidics, and medical implant treatment. For many of these applications, precise control of surface roughness after laser treatment is crucial, as it directly affects the final properties of the work surface. However, achieving low mean surface roughness values (<100 nm) is challenging due to the fundamental principles of laser light–matter interactions. The complex physical processes that occur during laser material interactions make it difficult to achieve the desired surface roughness, and only advanced scanning methods can potentially solve this issue. In our study, we analyzed laser scanning algorithms to determine the optimal method for producing surfaces with minimal roughness. We investigated how scanning parameters such as the overlap of modifications, the amount of successive line shift, and laser-scanner synchronization impact surface roughness. Using a numerical model, we obtained results that showed good agreement with experimentally acquired data. Our detailed theoretical and experimental analysis of different scanning methods can provide valuable information for the future optimization of minimal-roughness micromachining.