Cellulose hydrogels, formed either through physical or chemical cross-linking into a three-dimensional network from cellulose or its derivatives, are renowned for their exceptional water absorption capacities and biocompatibility. Rising demands for sustainable materials have spurred interest in cellulose hydrogels, attributed to their abundant supply, biodegradability, and non-toxic nature. These properties highlight their extensive potential across various sectors including biomedicine, the food industry, and environmental protection. Cellulose hydrogels are particularly advantageous in applications such as drug delivery, wound dressing, and water treatment. Recent large-scale studies have advanced our understanding of cellulose preparation and its applications. This review delves into the fundamental concepts, preparation techniques, and current applications of cellulose hydrogels in diverse fields. It also discusses the latest advances in nano-lignin-based hydrogels, providing a comprehensive overview of this promising material and offering insights and guidance for future research and development.
Here, we fabricate poly(vinylidene fluoride-co-hexafluoropropene) (PVDF-co-HFP) by electrospinning for a gel polymer electrolyte (GPE) for use in flexible Li-ion batteries (LIBs). As a solvent, we use N-methyl-2-pyrrolidone (NMP), which helps produce the cross-linked morphology of PVDF-co-HFP separator, owing to its low volatility. The cross-linked PVDF-co-HFP separator shows an uptake rate higher than that of a commercialized polypropylene (PP) separator. Moreover, the PVDF-co-HFP separator shows an ionic conductivity of 2.3 × 10−3 S/cm at room temperature, comparable with previously reported values. An LIB full-cell assembled with the PVDF-co-HFP-based GPE shows capacities higher than its counterpart with the commercialized PP separator, confirming that the cross-linked PVDF-co-HFP separator provides highly efficient ionic conducting pathways. In addition, we integrate a flexible LIB cell using the PVDF-co-HFP GPE with a flexible organic light emitting diode (OLED), demonstrating a fully flexible unit of LIB and OLED.
1 February 2022 in Journal of Colloid and Interface Science
This study reports the kinetics of the bonding process of a Cu bump/ thick Sn bonding layer/Cu bump bonding structure, popularly adopted for three-dimensional (3D) packaging, and the mechanical properties of the joints. Characterizing the bonding morphologies of the joints using scanning electron microscopy disclosed that a drastic intermetallic phase transformation occurred around the melting temperature of Sn in a manner similar to the wetting process of SnPb solder on Cu. We also delved into the mechanical behavior of the joints using lap-shear testing to illuminate that a unique feature of the joints is a lack of ductility. In addition, the samples exhibited a sensitive dependence of the joint strength on the bonding conditions (temperature and pressure).
12 September 2017 in Micro and Nano Systems Letters
Pt thin film temperature sensors (Pt T sensors) are embedded in micro gas sensors to measure and control the working temperature. We characterized electrical resistances of Pt T sensors and micro heaters with temperature changing in the oven and by Joule heating. In order to enhance the accuracy of temperature measurement by the Pt T sensors, we investigated the correlation among the Pt T sensor, micro heater, and the working temperature, which was linear proportional relation expressed as the equation: T2 = 6.466R1–642.8, where T2 = temperature of the Pt micro heater and R1 = the electrical resistance of the Pt T sensor. As the error by physically separated gap between Pt T sensor and micro heater calibrated, measuring and controlling temperature of micro heater in micro gas sensors were possible through the Pt T sensors. For the practical use of Pt T sensor in micro gas sensor, the gas sensing properties of fabricated micro gas sensors to 25 ppm CO and 1 ppm HCHO gases were characterized.
High theoretical capacity and low-cost copper sulfide (CuxS)-based anodes have gained great attention for advanced sodium-ion batteries (SIBs). However, their practical application may be hindered due to their unstable cycling performance and problems with the dissolution of sodium sulfides (NaxS) into electrolyte. Here, we employed metal organic framework (MOF-199) as a sacrificial template to fabricate nanoporous CuxS with a large surface area embedded in the MOF-derived carbon network (CuxS-C) through a two-step process of sulfurization and carbonization via H2S gas-assisted plasma-enhanced chemical vapor deposition (PECVD) processing. Subsequently, we uniformly coated a nanocarbon layer on the Cu1.8S-C through hydrothermal and subsequent annealing processes. The physico-chemical properties of the nanocarbon layer were revealed by the analytical techniques of high-resolution transmission electron microscopy (HRTEM), energy-dispersive X-ray spectroscopy (EDS), and scanning electron microscopy (SEM). We acquired a higher SIB performance (capacity retention (~93%) with a specific capacity of 372 mAh/g over 110 cycles) of the nanoporous Cu1.8S-C/C core/shell anode materials than that of pure Cu1.8S-C. This encouraging SIB performance is attributed to the key roles of a nanocarbon layer coated on the Cu1.8S-C to accommodate the volume variation of the Cu1.8S-C anode structure during cycling, enhance electrical conductivity and prevent the dissolution of NaxS into the electrolyte. With these physico-chemical and electrochemical properties, we ensure that the Cu1.8S-C/C structure will be a promising anode material for large-scale and advanced SIBs.