BaFe1−xCuxO3 perovskites (x = 0, 0.1, 0.3 and 0.4) have been synthetized, characterized and tested for soot oxidation in both Diesel and Gasoline Direct Injection (GDI) exhaust conditions. The catalysts have been characterized by BET, ICP-OES, SEM-EDX, XRD, XPS, H2-TPR and O2-TPD and the results indicate the incorporation of copper in the perovskite lattice which leads to: (i) the deformation of the initial hexagonal perovskite structure for the catalyst with the lowest copper content (BFC1), (ii) the modification to cubic from hexagonal structure for the high copper content catalysts (BFC3 and BFC4), (iii) the creation of a minority segregated phase, BaOx-CuOx, in the highest copper content catalyst (BFC4), (iv) the rise in the quantity of oxygen vacancies/defects for the catalysts BFC3 and BFC4, and (v) the reduction in the amount of O2 released in the course of the O2-TPD tests as the copper content increases. The BaFe1−xCuxO3 perovskites catalyze both the NO2-assisted diesel soot oxidation (500 ppm NO, 5% O2) and, to a lesser extent, the soot oxidation under fuel cuts GDI operation conditions (1% O2). BFC0 is the most active catalysts as the activity seems to be mainly related with the amount of O2 evolved during an. O2-TPD, which decreases with copper content.
A series of BaMnO3 solids (BM-CX) were prepared by a modified sol-gel method in which a carbon black (VULCAN XC-72R), and different calcination temperatures (600–850 °C) were used. The fresh and used catalysts were characterized by ICP-OES, XRD, XPS, FESEM, TEM, O2-TPD and H2- TPR-. The characterization results indicate that the use of low calcination temperatures in the presence of carbon black allows decreasing the sintering effects and achieving some improvements regarding BM reference catalyst: (i) smaller average crystal and particles size, (ii) a slight increase in the BET surface area, (iii) a decrease in the macropores diameter range and, (iv) a lower temperature for the reduction of manganese. The hydrogen consumption confirms Mn(III) and Mn(IV) are presented in the samples, Mn(III) being the main oxidation state. The BM-CX catalysts series shows an improved catalytic performance regarding BM reference catalyst for oxidation processes (NO to NO2 and NO2-assisted soot oxidation), promoting higher stability and higher CO2 selectivity. BM-C700 shows the best catalytic performance, i.e., the highest thermal stability and a high initial soot oxidation rate, which decreases the accumulation of soot during the soot oxidation and, consequently, minimizes the catalyst deactivation.
The NOx storage mechanism on BaTi0.8Cu0.2O3 catalyst were studied using different techniques. The results obtained by XRD, ATR, TGA and XPS under NOx storage–regeneration conditions revealed that BaO generated on the catalyst by decomposition of Ba2TiO4 plays a key role in the NOx storage process. In situ DRIFTS experiments under NO/O2 and NO/N2 show that nitrites and nitrates are formed on the perovskite during the NOx storage process. Thus, it seems that, as for model NSR catalysts, the NOx storage on BaTi0.8Cu0.2O3 catalyst takes place by both “nitrite” and “nitrate” routes, with the main pathway being highly dependent on the temperature and the time on stream: (i) at T < 350 °C, NO adsorption leads to nitrites formation on the catalyst and (ii) at T > 350 °C, the catalyst activity for NO oxidation promotes NO2 generation and the nitrate formation.
Gasoline engines, mainly gasoline direct injection engines (GDI) require, in addition to three-way catalysts (TWC), a new catalytic system to remove the formed soot. Gasoline Particle Filters (GPF) are, among others, a possible solution. BaMnO3 and copper-doped BaMnO3 perovskites seem to be a feasible alternative to current catalysts for GPF. The physical and chemical properties of these two perovskites determining the catalytic performance have been modified using different synthesis routes: (i) sol-gel, (ii) modified sol-gel and iii) hydrothermal. The deep characterization allows concluding that: (i) all samples present a perovskite-like structure (hexagonal), except BMC3 which shows a polytype one (due to the distortion caused by copper insertion in the lattice), and ii) when a low calcination temperature is used during synthesis, the sintering effect decreases and the textural properties, the reducibility and the oxygen mobility are improved. The study of soot oxidation simulating the hardest GDI scenarios reveals that, as for diesel soot removal, the best catalytic performance involves the presence of oxygen vacancies to adsorb and activate oxygen and a labile Mn (IV)/Mn (III) redox pair to dissociate the adsorbed oxygen. The combination of both properties allows the transport of the dissociated oxygen towards the soot.
14 July 2010 in Journal of Applied Polymer Science
The effect of partial Ti substitution by Mn, Fe, Co, or Cu on the NOx storage capacity (NSC) of a BaTi0.8B0.2O3 lean NOx trap (LNT) catalyst has been analyzed. The BaTi0.8B0.2O3 catalysts were prepared using the Pechini’s sol–gel method for aqueous media. The characterization of the catalysts (BET, ICP-OES, XRD and XPS) reveals that: i) the partial substitution of Ti by Mn, Co, or Fe changes the perovskite structure from tetragonal to cubic, whilst Cu distorts the raw tetragonal structure and promotes the segregation of Ba2TiO4 (which is an active phase for NOx storage) as a minority phase and ii) the amount of oxygen vacancies increases after partial Ti substitution, with the BaTi0.8Cu0.2O3 catalyst featuring the largest amount. The BaTi0.8Cu0.2O3 catalyst shows the highest NSC at 400 °C, based on NOx storage cyclic tests, which is within the range of highly active noble metal-based catalysts.