BaFe1−xCuxO3 perovskites (x = 0, 0.1, 0.3 and 0.4) have been synthetized, characterized and tested for soot oxidation in both Diesel and Gasoline Direct Injection (GDI) exhaust conditions. The catalysts have been characterized by BET, ICP-OES, SEM-EDX, XRD, XPS, H2-TPR and O2-TPD and the results indicate the incorporation of copper in the perovskite lattice which leads to: (i) the deformation of the initial hexagonal perovskite structure for the catalyst with the lowest copper content (BFC1), (ii) the modification to cubic from hexagonal structure for the high copper content catalysts (BFC3 and BFC4), (iii) the creation of a minority segregated phase, BaOx-CuOx, in the highest copper content catalyst (BFC4), (iv) the rise in the quantity of oxygen vacancies/defects for the catalysts BFC3 and BFC4, and (v) the reduction in the amount of O2 released in the course of the O2-TPD tests as the copper content increases. The BaFe1−xCuxO3 perovskites catalyze both the NO2-assisted diesel soot oxidation (500 ppm NO, 5% O2) and, to a lesser extent, the soot oxidation under fuel cuts GDI operation conditions (1% O2). BFC0 is the most active catalysts as the activity seems to be mainly related with the amount of O2 evolved during an. O2-TPD, which decreases with copper content.
Mixed oxides with perovskite-type structure (ABO3) are promising catalysts for atmospheric pollution control due to their interesting and tunable physicochemical properties. In this work, two series of BaxMnO3 and BaxFeO3 (x = 1 and 0.7) catalysts were synthesized using the sol–gel method adapted to aqueous medium. The samples were characterized by μ-XRF, XRD, FT-IR, XPS, H2-TPR, and O2-TPD. The catalytic activity for CO and GDI soot oxidation was determined by temperature-programmed reaction experiments (CO-TPR and soot-TPR, respectively). The results reveal that a decrease in the Ba content improved the catalytic performance of both catalysts, as B0.7M-E is more active than BM-E for CO oxidation, and B0.7F-E presents higher activity than BF for soot conversion in simulated GDI engine exhaust conditions. Manganese-based perovskites (BM-E and B0.7M-E) achieve better catalytic performance than iron-based perovskite (BF) for CO oxidation reaction due to the higher generation of actives sites.
Gasoline engines, mainly gasoline direct injection engines (GDI) require, in addition to three-way catalysts (TWC), a new catalytic system to remove the formed soot. Gasoline Particle Filters (GPF) are, among others, a possible solution. BaMnO3 and copper-doped BaMnO3 perovskites seem to be a feasible alternative to current catalysts for GPF. The physical and chemical properties of these two perovskites determining the catalytic performance have been modified using different synthesis routes: (i) sol-gel, (ii) modified sol-gel and iii) hydrothermal. The deep characterization allows concluding that: (i) all samples present a perovskite-like structure (hexagonal), except BMC3 which shows a polytype one (due to the distortion caused by copper insertion in the lattice), and ii) when a low calcination temperature is used during synthesis, the sintering effect decreases and the textural properties, the reducibility and the oxygen mobility are improved. The study of soot oxidation simulating the hardest GDI scenarios reveals that, as for diesel soot removal, the best catalytic performance involves the presence of oxygen vacancies to adsorb and activate oxygen and a labile Mn (IV)/Mn (III) redox pair to dissociate the adsorbed oxygen. The combination of both properties allows the transport of the dissociated oxygen towards the soot.
The ongoing search for innovative and environmentally friendly luminescent materials coupled with customizable physical and chemical properties at the nanoscale positions carbon dots (CDots) as ideal candidates for photonic applications. However, even today, their rational design for specific applications remains elusive due to the unknown relationship between optical and structural properties. Therefore, this study aims to fill this gap by linking the chemical structure of the precursor and synthetic conditions to the final structural composition of the CDots and, by extension, to their optical properties. The study shows that while CDots are chemically stable, their optical properties, which are determined by the carbonaceous core and surface groups, are highly pH dependent. These properties, together with the long fluorescence lifetimes observed in living cells (>10 ns), make these biomass‐derived CDots promising probes for time‐resolved fluorescence imaging.
The effect of partial Ti substitution by Mn, Fe, Co, or Cu on the NOx storage capacity (NSC) of a BaTi0.8B0.2O3 lean NOx trap (LNT) catalyst has been analyzed. The BaTi0.8B0.2O3 catalysts were prepared using the Pechini’s sol–gel method for aqueous media. The characterization of the catalysts (BET, ICP-OES, XRD and XPS) reveals that: i) the partial substitution of Ti by Mn, Co, or Fe changes the perovskite structure from tetragonal to cubic, whilst Cu distorts the raw tetragonal structure and promotes the segregation of Ba2TiO4 (which is an active phase for NOx storage) as a minority phase and ii) the amount of oxygen vacancies increases after partial Ti substitution, with the BaTi0.8Cu0.2O3 catalyst featuring the largest amount. The BaTi0.8Cu0.2O3 catalyst shows the highest NSC at 400 °C, based on NOx storage cyclic tests, which is within the range of highly active noble metal-based catalysts.