The present research aims to describe a new methodology to obtain biocompatible hydrogels based on Aloe vera used for wound healing applications. The properties of two hydrogels (differing in Aloe vera concentration, AV5 and AV10) prepared by an all-green synthesis method from raw, natural, renewable and bioavailable materials such as salicylic acid, allantoin and xanthan gum were investigated. The morphology of the Aloe vera based hydrogel biomaterials was studied by SEM analysis. The rheological properties of the hydrogels, as well as their cell viability, biocompatibility and cytotoxicity, were determined. The antibacterial activity of Aloe vera based hydrogels was evaluated both on Gram-positive, Staphylococcus aureus and on Gram-negative, Pseudomonas aeruginosa strains. The obtained novel green Aloe vera based hydrogels showed good antibacterial properties. In vitro scratch assay demonstrated the capacity of both AV5 and AV10 hydrogels to accelerate cell proliferation and migration and induce closure of a wounded area. A corroboration of all morphological, rheological, cytocompatibility and cell viability results indicates that this Aloe vera based hydrogel may be suitable for wound healing applications.

The removal of pharmaceutical contaminants from wastewater has gained considerable attention in recent years, particularly in the advancements of hydrogel-based adsorbents as a green solution for their ease of use, ease of modification, biodegradability, non-toxicity, environmental friendliness, and cost-effectiveness. This study focuses on the design of an efficient adsorbent hydrogel based on 1% chitosan, 40% polyethylene glycol 4000 (PEG4000), and 4% xanthan gum (referred to as CPX) for the removal of diclofenac sodium (DCF) from water. The interaction between positively charged chitosan and negatively charged xanthan gum and PEG4000 leads to strengthening of the hydrogel structure. The obtained CPX hydrogel, prepared by a green, simple, easy, low-cost, and ecological method, has a higher viscosity due to the three-dimensional polymer network and mechanical stability. The physical, chemical, rheological, and pharmacotechnical parameters of the synthesized hydrogel were determined. Swelling analysis demonstrated that the new synthetized hydrogel is not pH-dependent. The obtained adsorbent hydrogel reached the adsorption capacity (172.41 mg/g) at the highest adsorbent amount (200 mg) after 350 min. In addition, the adsorption kinetics were calculated using a pseudo first-order model and Langmuir and Freundlich isotherm parameters. The results demonstrate that CPX hydrogel can be used as an efficient option to remove DCF as a pharmaceutical contaminant from wastewater.

Multifunctional composite coatings composed of metal oxide nanoparticles dispersed in polymer matrices are an advanced solution to solve the problem of stone heritage deterioration. Their innovative design is meant to be stable, durable, transparent, easy to apply and remove, non-toxic, hydrophobic, and permeable. Coating formulations for the protection of buildings and monuments have been intensively researched lately. Such formulations are based on multifunctional composite coatings incorporating metal oxides. The present work aims to combine the hydrophobic properties of sodium polyacrylate (NaPAC₁₆) with the antimicrobial effectiveness, with promising antimicrobial results even in the absence of light, and good compatibility of MgO (a safe to use, low cost and environmentally friendly material) and TiO₂ (with antibacterial and antifungal properties), in order to develop coatings for stone materials protection. MgO (pure phase periclase) and TiO₂ (pure phase anatase) nanopowders were prepared through sol–gel method, specifically routes. Aqueous dispersions of hydrophobically modified polymer (NaPAC₁₆, polyacrylic acid sodium salt) and MgO/TiO₂ nanopowders were deposited through layer-by-layer dip coating technique on glass slides and through immersion on stone fragments closely resembling the mosaic stone from the fourth century AD Roman Mosaic Edifice, from Constanta, Romania. The oxide nanopowders were characterized by: Thermal analysis (TG/DTA), scanning electron microscopy (SEM), X-ray diffraction (XRD), BET specific surface area and porosity, and UV–Vis spectroscopy for band gap determination. An aqueous dispersion of modified polyacrylate polymer and oxide nanopowders was deposited on different substrates (glass slides, red bricks, gypsum mortars). Film hydrophobicity was verified by contact angle measurements. The colour parameters were evaluated. Photocatalytic and antimicrobial activity of the powders and composite coatings were tested.