Structural Health Monitoring (SHM) takes advantage of the recent advances in nanotechnology and sensing in order to monitor the behavior of a structure, assess its performance and identify damage at an early stage. Monitoring the state of strain throughout an entire structure is essential to determine its state of stress, detect potential residual stresses after fabrication, and also to help to establish its integrity. The Carbon nanotube thread was integrated into three-dimensional braiding materials and used for the first time as a sensor to monitor strain and also to detect damage in the three-dimensional braided composite material.In this paper a literature review about the application of carbon nanotubes thread for sensors and smart materials used for SHM of braiding structures is presented. The test data show the braided angle is important parameter for structural health monitoring of three-dimensional. The research will provide a new integrated and distributed technologies for the built-in carbon nanotube sensor to detect the health of composite. The subject will provide the new idea and method for the development of smart composite materials research and application.
The bending properties of three-dimensional (3Dim) and five-directional (5Dir) braided/epoxy resin composites at room temperature, 90 °C, 110 °C, and 150 °C and heating for 0.25 h, 10 h, and 30 h, respectively, were studied. The effect of different temperatures and heating times on the bending property of these composites was discussed. The results showed that the bending strength of these composites at 90 °C, 110 °C, and 150 °C and heating time of 0.25 h is 33.86%, 46.27%, and 83.94% lower, respectively, than that at room temperature. In addition, 3Dim–5Dir braided composites exhibit different damage modes at different temperatures, revealing different failure mechanisms. Heating temperature has greater influence on the bending properties of these composites than heating time. The results provided a basis for the application of resin-based 3Dim–5Dir braided/epoxy resin composites at different temperatures.
Acoustic emission (AE) source localization is one of the important purposes of nondestructive testing. The localization accuracy reflects the degree of coincidence between the identified location and the actual damage location. However, the anisotropy of carbon fiber three-dimensional braided composites will have a great impact on the accuracy of AE source location. In order to solve this problem, the time-frequency domain characteristics of AE signals in a carbon fiber braided composite tensile test were analyzed by Hilbert–Huang transform (HHT), and the corresponding relationship between damage modes and AE signals was established. Then, according to the time-frequency characteristics of HHT of tensile acoustic emission signals, the two-step method was used to locate the damage source. In the first step, the sound velocity was compensated by combining the time-frequency analysis results with the anisotropy of the experimental specimens, and the four-point circular arc method was used to locate the initial position. In the second step, there is an improvement of the Drosophila optimization algorithm, using the ergodicity of the chaotic algorithm and congestion adjustment mechanism in the fish swarm algorithm. The smoothing parameters and function construction in the probabilistic neural network were optimized, the number of iterations was reduced, the location accuracy was improved, and the damage mode of composite materials was obtained. Then, the damage location was obtained to achieve the purpose of locating the damage source.
The identification and classification of acoustic emission (AE) based failure modes are complex due to the fact that AE waves are generally released simultaneously from all AE-emitting damage sources. To fully understand the occurrence of damage and the damage evolution law of 3D braided composites, the tensile response characteristics and failure mechanisms of such composites were revealed by experiments, followed by frequency domain analyses. The results indicated good correlation between the number of AE events and the evolution of damage in 3D braided composites. After an AE signal was decomposed by the Hilbert–Huang transform (HHT) method, it might extract and separate all damage modes included in this AE signal. Additionally, the frequency saltation in the HHT spectra implied changes in the failure mode of the 3D braided composites. This study provides an effective new method for the analysis of the tensile fracture mechanism in 3D braided composites.
Variant programming is regarded as a parametric design in literal and fundamental sense. Some parametric pattern models based on constraints are constructed by a sequence of operation and dimensional formula, not geometric constraints. In our previous work, parametric pattern-making model is created by geometric constraint graph. After surveying dimensional constraints in the other fields, this paper proposes complete parametric pattern-making model, including geometric entities, geometric constraints, dimensional constraints, measurement parameters and parameter constraints. Parameter constraints consist of difference, ratio and linear formula between measurement parameters, implemented by adjacent list of parameter constraints to keep body measurement parameters consistent. Moreover, the range of dimensional parameters is discussed further to explore the relation between measurement and dimensional parameters.
19 November 2019 in Journal of Testing and Evaluation
An important method for making smart three-dimensional (3-D) braiding composites is to use embedded carbon nanotube (CNT) yarn sensors with 3-D braiding technology. According to the braiding structure of 3-D six-direction braiding composites, the mathematical model of carrier movement of braiding machine is constructed. The method for calculating the number and length of embedded CNT yarns with intelligent composites is proposed. The characteristics of resistance changing for CNT yarns under loading are analyzed. Experiments show that the error of the length and actual length of the CNT yarn calculated by the Bezier curve is less than 1 %. When the tensile strain exceeds 2 %, the strain of the embedded CNT yarns begins to appear nonlinear. The loading and unloading of the specimen have some influence on the resistance change of the CNT yarn. After the load is unloaded, the CNT yarn will produce the residual resistance.