Antennas are a vital component of the wireless body sensor networks devices. A wearable antenna in this system can be used as a communication component or energy harvester. This paper presents a detailed review to recent advances fabrication methods for flexible antennas. Such antennas, for any applications in wireless body sensor networks, have specific considerations such as flexibility, conformability, robustness, and ease of integration, as opposed to conventional antennas. In recent years, intriguing approaches have demonstrated antennas embroidered on fabrics, encapsulated in polymer composites, printed using inkjets on flexible laminates and a 3-D printer and, more interestingly, by injecting liquid metal in microchannels. This article presents an operational perspective of such advanced approaches and beyond, while analyzing the strengths and limitations of each in the microwave as well as millimeter-wave regions. Navigating through recent developments in each area, mechanical and electrical constitutive parameters are reviewed, and finally, some open challenges are presented as well for future research directions.

A novel method is presented to design single-feed high-gain EBG resonator antennas (ERAs) with significantly wider bandwidths. Dielectric contrast is introduced to 1-D EBG superstructures composed of unprinted dielectric slabs, and the thicknesses of each of these slabs is optimized to achieve a wideband defect mode in a unit-cell model. Next, antennas are designed and their superstructure areas are truncated to increase the antenna bandwidth and aperture efficiency while decreasing antenna footprint. We demonstrate that a small superstructure area increases the 3-dB bandwidth of ERAs significantly. A prototype ERA designed with a single feed and superstructure area as small as 1.5 λ ₀ ×1.5 λ ₀ has a measured 3-dB directivity bandwidth of 22% at a peak gain of 18.2 dBi. This prototype antenna was made out of three slabs of different dielectric constants, two of them touching each other. This prototype demonstrates more than 85% reduction in the ERA footprint alongside a drastic improvement in bandwidth over the 3%-4% measured bandwidth of the classical single-feed ERAs with unprinted slabs.

A simple conformal ultrawideband (UWB) antenna with monopole-like radiation patterns is proposed in this communication. To achieve the wide bandwidth, two rings are arranged concentrically around the main annular-ring circular patch antenna, in which two rectangular slots are added. The antenna has monopole-like radiation patterns generated by combining four propagation modes of TM ₀₁ , TM ₀₂ , TM ₀₃ , and TM ₀₄ throughout the operating bands. To enhance the flexibility and robustness, the proposed antenna is fabricated using conductive fabric embedded into polydimethylsiloxane (PDMS) polymer. To our knowledge, this is the first flexible UWB antenna with monopole-like radiation patterns reported in the open literature. The measured results show that the antenna achieves a 10 dB return loss bandwidth from 2.85 to 8.6 GHz. Monopole-like radiation patterns are maintained throughout the frequency band, agreeing well with simulated results. This has been validated through the measured mean realized gain (MRG) pattern from 2.85 to 8.6 GHz. The fabricated antenna was bent and tested at various curvatures to verify its conformability. To evaluate suitability for UWB communications, the system-fidelity factors of the antenna are investigated using full-wave analysis in CST Microwave Studio, in both flat and bent conditions, validating its potential for UWB pulse transmission.

Extremely wideband resonant cavity antennas (RCAs) with large directivity-bandwidth products (DBPs) are presented. Their distinct feature is a single-slab superstrate that has a permittivity gradient in the directions transverse to the antenna axis. The application of such a superstrate in a single-feed RCA improves the DBP by a factor of three or more as compared with superstrates composed of uniform dielectric slabs. Their very small area enables an antenna designer to achieve unprecedented figures of DBP per unit area, from a simple planar antenna. Prototype RCAs have been fabricated and measurements have validated the concept. A measured 3-dB directivity bandwidth of 52.9% was demonstrated with a measured directivity of 16.4 dBi for an RCA that has a very small total footprint area of 1.54$\lambda_0^2$ at the lowest operating frequency (2.84$\lambda_{0,c}^2$ at the center frequency). This represents an increase of 90% over the previous best measured RCA directivity bandwidth of 28%.

In this paper, a detailed investigation of the realization of conformal wearable transparent antennas by integrating conductive mesh with polymer has been presented. The proposed realization method is much simpler and more cost-effective than the existing realization methods of transparent antennas, and the prototype fabricated from the selected composite materials is more flexible and robust in bending operations than other transparent antennas. In this paper, the mechanical, electrical, and optical characteristics of the proposed composite material have been investigated to analyze its suitability for transparent flexible antenna realization. For concept demonstration, a prototype of a dual-band antenna operating at 2.33-2.53 GHz and 4.7-5.6 GHz has been fabricated and tested. These frequencies cover both the instrument, scientific, and measurement (ISM) and the wireless local area network (WLAN) bands. Full ground plane is utilized in the antenna design for on-body operations. The suitability of the antenna for wearable applications has been investigated by measuring its performance under physical deformation and testing its performance on phantom. Next, the RF performance of the antenna has been improved by using two layers of conductor to form the radiating element. Although transparency is slightly compromised, the double-layer element improves the gain and efficiency of the antenna.

In this paper we present a new approach to realize flexible transparent strain sensors. It combines the use of transparent conductive fabric with polydimethylsiloxane (PDMS) through a simple and straightforward layer-by-layer assembly process. The conductive fabric is used to realize the transparent electrodes while the PDMS is utilized as both the substrate and encapsulation layers. As a concept demonstration, an interdigital capacitive sensor is designed and fabricated using the proposed approach. The fabricated sensor is then characterized in terms of its transparency and electro-mechanical nature. This is followed by the application of the sensor in several physiological sensing scenarios including the sensing of various body-part movements and tactile sensing. Apart from a high optical transparency (~70%), the sensor shows promising sensing results which validate the applicability of the proposed approach for realization of flexible and transparent strain sensors for wearable sensing applications.