Nafion composite membranes, containing different amounts of mesoporous sulfated titanium oxide (TiO2-SO4) were prepared by solvent-casting and tested in proton exchange membrane fuel cells (PEMFCs), operating at very low humidification levels. The TiO2-SO4 additive was originally synthesized by a sol-gel method and characterized through x-ray diffraction (XRD), scanning electron microscopy (SEM), thermogravimetric analysis (TGA) and ion exchange capacity (IEC). Peculiar properties of the composite membranes, such as the thermal transitions and ion exchange capacity, were investigated and here discussed. When used as an electrolyte in the fuel cell, the composite membrane guaranteed an improvement with respect to bare Nafion systems at 30% relative humidity and 110 °C, exhibiting higher power and current densities.
Manufacturing new electrolytes with high ionic conductivity has been a crucial challenge in the development and large-scale distribution of fuel cell devices. In this work, we present two Nafion composite membranes containing a non-stoichiometric calcium titanate perovskite (CaTiO3−δ) as a filler. These membranes are proposed as a proton exchange electrolyte for Polymer Electrolyte Membrane (PEM) fuel cell devices. More precisely, two different perovskite concentrations of 5 wt% and 10 wt%, with respect to Nafion, are considered. The structural, morphological, and chemical properties of the composite membranes are studied, revealing an inhomogeneous distribution of the filler within the polymer matrix. Direct methanol fuel cell (DMFC) tests, at 110 °C and 2 M methanol concentration, were also performed. It was observed that the membrane containing 5 wt% of the additive allows the highest cell performance in comparison to the other samples, with a maximum power density of about 70 mW cm−2 at 200 mA cm−2. Consequently, the ability of the perovskite structure to support proton carriers is here confirmed, suggesting an interesting strategy to obtain successful materials for electrochemical devices.
A non-stoichiometric calcium titanate CaTiO3-δ (CTO) was synthesized and used as oxygen reduction reaction co-catalyst (together with Pt/C) in direct methanol fuel cells (DMFCs). A membrane-electrode assembly (MEA), equipped with a composite cathode formulation (Pt/C:CTO1:1), was investigated in DMFC, using a 2 M methanol solution at the anode and oxygen at the cathode, and compared with an MEA equipped with a benchmark Pt/C cathode catalyst. It appears that the presence of the CTO additive promotes the oxygen reduction reaction (ORR) due to the presence of oxygen vacancies as available active sites for oxygen adsorption in the lattice. The increase in power density obtained with the CTO-based electrode, compared with the benchmark Pt/C, was more than 40% at 90 °C, reaching a maximum power density close to 120 mW cm−2, which is one of the highest values reported in the literature under similar operating conditions.
Organic–inorganic hybrid electrolytes based on Al-doped Li7La3Zr2O12 (LLZO) and two different ionic liquids (ILs), namely N-ethoxyethyl-N-methylpiperidinium bis(fluorosulfonyl)imide (FSI IL) and N-ethoxyethyl-N-methylpiperidinium difluoro(oxalato)borate (DFOB IL), were prepared with the aim of improvement of inherent flexibilities of inorganic solid electrolytes. The composites were evaluated in terms of thermal, spectroscopical, and electrochemical properties. In the impedance spectra of LLZO composites with 15 wt% ILs, a semi-circle due to grain boundary resistances was not observed. With the sample merely pressed with 1 ton, without any high-temperature sintering process, the ionic conductivity of 10−3 S cm−1 was achieved at room temperature. Employing a ternary composite of LLZO, FSI IL, and LiFSI as an electrolyte, all-solid-state lithium metal batteries having LiFePO4 as a cathode were assembled. The cell exhibited a capacity above 100 mAh g−1 throughout the course of charge–discharge cycle at C/20. This confirms that FSI IL is an effective additive for inorganic solid electrolytes, which can guarantee the ion conduction.
A composite membrane based on a Nafion polymer matrix incorporating a non-stoichiometric calcium titanium oxide (CaTiO3−δ) additive was synthesized and characterized by means of thermal analysis, dynamic mechanical analysis, and broadband dielectric spectroscopy at different filler contents; namely two concentrations of 5 and 10 wt.% of the CaTiO3−δ additive, with respect to the dry Nafion content, were considered. The membrane with the lower amount of additive displayed the highest water affinity and the highest conductivity, indicating that a too-high dose of additive can be detrimental for these particular properties. The mechanical properties of the composite membranes are similar to those of the plain Nafion membrane and are even slightly improved by the filler addition. These findings indicate that perovskite oxides can be useful as a water-retention and reinforcing additive in low-humidity proton-exchange membranes.
The oxygen reduction reaction (ORR) is an important challenge in the development and large-scale distribution of energy conversion devices, especially low-temperature proton exchange membrane (PEM) fuel cells. In order to speed up the ORR kinetics and improve fuel cell performance, iron-doped calcium titanate (CTFO) is proposed as a cocatalyst. Fundamental physical and chemical characterizations by means of X-ray diffraction, infrared spectroscopy, and morphological and thermal analyses for the understanding of the functional features of the proposed materials were carried out. Composite catalysts containing different amounts of CTFO additive with respect to platinum (i.e., Pt:CTFO 1:0.5 and 1:1 wt:wt) were studied using a rotating disk electrode (RDE). Fuel cell tests were performed at 80 °C under 30% and 80% relative humidity. The best Pt:CTFO composite catalyst was compared to a bare Pt/C and a Pt/C:CaTiO3−δ 1:1 catalyst, revealing superior performances of the latter at high relative humidity fuel cell operation, as a combined result of an optimized electrolyte-electrode interface and improved ORR kinetics due to the inorganic additive.