Multiphase-flow oscillating heat transfer is a kind of highly efficient heat transfer method. In this article, two turbulence models are used to simulate the oscillating heat transfer process. Results include qualitative and quantitative comparisons with experimental data. We find that, in both a closed cavity and an open oil cooling gallery, the SST k–ω model performs better in the simulation of oscillating movement, as well as in the heat transfer effect prediction. The error of the heat transfer coefficient begins to increase with at increasing Reynolds number, illustrating that the SST k–ω model has higher accuracy at low Reynolds numbers.
4 August 2015 in Journal of Materials Engineering and Performance
In order to evaluate the elevated temperature creep performance of the ABOw/Al–12Si composite as a prospective piston crown material, the tensile creep behaviors and creep fracture mechanisms have been investigated in the temperatures range from 250 to 400 °C and the stress range from 50 to 230 MPa using a uniaxial tensile creep test. The creep experimental data can be explained by the creep constitutive equation with stress exponents of 4.03–6.02 and an apparent activation energy of 148.75 kJ/mol. The creep resistance of the ABOw/Al–12Si composite is immensely improved by three orders of magnitude, compared with the unreinforced alloy. The analysis of the ABOw/Al–12Si composite creep data revealed that dislocation climb is the main creep deformation mechanism. The values of the threshold stresses are 37.41, 25.85, and 17.36 at elevated temperatures of 300, 350 and 400 °C, respectively. A load transfer model was introduced to interpret the effect of whiskers on the creep rate of this composite. The creep test data are very close to the predicted values of the model. Finally, the fractographs of the specimens were analyzed by Scanning Electron Microscope (SEM), the fracture mechanisms of the composites at different temperatures were investigated. The results showed that the fracture characteristic of the ABOw/Al–12Si composite exhibited a macroscale brittle feature range from 300 to 400 °C, but a microscopically ductile fracture was observed at 400 °C. Additionally, at a low tensile creep temperature (300 °C), the plastic flow capacity of the matrix was poor, and the whisker was easy to crack and fracture. However, during tensile creep at a higher temperature (400 °C), the matrix was so softened that the whiskers were easily pulled out and interfacial debonding appeared.
Thermal contact resistance between interfaces is an important parameter in the analysis of temperature distribution for structural components. Thermal contact resistance between heat resistant steel 2Cr12NiMoWV/aluminum alloy BH137 interfaces and 2Cr12NiMoWV/titanium alloy ?-TiAl interfaces were experimentally investigated in the present paper. The effects of contact pressure and interface tem-perature were detailed. The temperature of contacting surfaces was from 80- 250?, and the contact pressure ranged from 2-17 MPa. All experiments were conducted in ambient atmosphere. Results showed that thermal contact resistance decreases with an increment of interface temperature or contact pressure. Under the same conditions of contact pressure and interface temperature, thermal contact resistance between 2Cr12NiMoWV and BH137 interfaces is lower than that between 2Cr12NiMoWV and ?-TiAl interfaces. The temperature dependence of thermal conductivity and mechanical properties was analyzed to explain the results. Furthermore, with the piston and piston pin as the research object, steady state temperature fields were simulated in cases of considering thermal contact resistance and without considering thermal contact resistance, respectively. The results showed that the maximum temperature of the piston pin will be lower when thermal contact resistance is considered.
In this paper, the heat transfer characteristics of spray-wall impingement on a high temperature wall were studied by using a transient thermocouple and a one-dimensional finite-difference conduction model to obtain variations of wall temperature and heat flux. Results showed that increasing the injection pressure and decreasing the ambient temperature both caused an increase in surface heat flux and heat transfer coefficient. However, with the increase of the initial surface temperature from 200 to 600 °C, the surface heat flux and heat transfer coefficient first increased and then decreased, and reached the maximum at about 520 °C and 390 °C respectively, which was due to the change of heat transfer regime on the wall. The contribution of experimental factors descended in the order of initial surface temperature, injection pressure and ambient temperature. The dimensionless surface heat fluxes in terms of Biot and Fourier numbers were highly similar and a dimensionless correlation was developed to quantify this heat transfer behavior, which showed that the ratio of the thermal resistance of the high temperature wall to the thermal resistance of convection heat transfer on the wall surface changed almost linearly during the process of spray-wall impingement.
The impact of liquid droplets on the ultracold surface affects significantly the cold start performance of internal combustion engines but the splash and spreading characteristics after impacting on the ultracold surface are not clearly understood. Therefore, droplets with various physical parameters impacting on the Al–Si alloy surface have been selected for the study under various surface temperatures (–40°C ≤ \(~{{T}_{s}}~\) ≤ 25°C) and droplet impact velocities (0.96 m/s ≤ \(~{{V}_{0}}~\) ≤ 3.52 m/s). The ultracold surface (\({{T}_{s}}\) = –40°C) is beneficial for corona splash, and droplets with the higher Oh number impacting on the ultracold surface easily produce corona splash as the main splash pattern. The ultracold surface assisted in enhancing the stability of the levitated lamella formation, and avoided the effects of rough surfaces, so the upper splash criterion is established to predict the transition from spreading to splash. The decreasing surface temperature reduces the maximum spreading diameter (\({{{{\beta }}}_{{{\text{max}},{\text{lt}}}}}\)) of low solidification point droplets (ethanol, n-propanol, and winter diesel). Based on the assumptions of qualitative temperature, the empirical correlation of the \({{{{\beta }}}_{{{\text{max}},{\text{lt}}}}}\) is created for the Ts from 25 to –40°C.